MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

Toyota Celica GT 2000- 2003 5 speed and automatic REMOVAL and INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 23-09-2011

Download
Remove the OBD canister, vacuum switching valve and air temperature control sensor from the air box
without removing any vacuum lines. Once all sensors have been removed take out the remaining air box
and air duct leading to the throttle body. Remove the two-piece air duct leading into the black ECU box.
We recommend you remove the front bumper to make the installation easier. The vacuum switching
valve used to control the valves or by-pass flaps in the box will no longer be used. These flaps control the
amount of air taken in when the engine is running. A 3mm cap will cap-off the port at the engine block.
2 Slip the 2 3/4” straight hose over the throttle body and use two clamps. Tighten the clamp on the throttle
body at this point. (See fig. 2) 3 Remove the black relay fuse box from the bracket bolted to the car frame. (See figs. 1) Remove the stock m6 bolt holding the bracket in place and set the OBD canister on top of the bracket. Screw
the stock bolt tight in place securing the OBD canister to the bracket. Take the vibra-mount and screw
it into the tapped hole right above the OBD canister. (See fig. 6) 4 Once the bumper has been removed cut an opening in the lower section of the plastic wheel well as seen in figure 3. A razor or any cutting device will work to make the opening

Incoming search terms:

2001 Honda GL1800 Oxygen Sensor Replacement Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
REPAIR PROCEDURE 1. Remove the top shelter (see page 2-10 in the Service Manual). 2. Remove the left and right O 2 sensors from the exhaust pipes. • You do not have to remove the exhaust pipes to remove the O 2 sensors. • Be sure to note the wire routing for proper reassembly. 3. Install the new O 2 sensors and route the wires properly (see pages 1-33 and 1-34 in the 2001- Service Manual). 4. Connect the black 4P female coupler of the sub- harness kit to the wire harness side black 4P male coupler (for the left-side O 2 sensor). 5. Connect the new left O 2 sensor to the black 4P coupler on the sub-harness. 6. Route the sub-harness from left to right, across the front edge of the fuel tank and secure it with the clip on the cruise actuator 7. Cut off the right 4P male O 2 sensor coupler (on the wire harness side). 8. Install a PVC cap onto the end of the Black/yellow wire and Green/red wire (these are the wires that were connected to the coupler that was removed in step 7). Fold each cap back and tape it securely to its wire; these wires are no longer used. • Do not cut the wires off, just tape them back. • The tape is supplied in the replacement kit. 9. Strip the ends of the White and Black/red wires (which were connected to the coupler that was removed in step 7) on the wire harness side and the 2P coupler on the sub-harness. Install a heat shrink tube on each wire of the sub harness. 10. Twist the ends of the White and Black/red wires of the sub-harness 2P coupler to the White and Black/red wires of the main harness. 11. Solder the wires using the solder from the kit. 12. Use a heat gun to secure the heat-shrink tubing over the soldered wires. 13. Connect the right O 2 sensor coupler to the white 4P male coupler on the sub harness.

Motorcycle Park sensor HRA – 7800 G2 User/ Installation Manual

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
Drill the holes in the bumper as indicated in the installation diagrams below and install the sensors. Sensors 1, 4, 5 and 8 should NOT be mounted on the curve of the bumper. 2. Install the sensor vertically; the “up” arrow must be pointing upwards. 3. Connect the Red wire of the control unit to the (+) positive of ignition wire. 4. Connect the Black wire (-) to the vehicleʼs chassis. 5. Connect yellow wire to the (+) positive wire of the vehicle reverse indicating light. 6. Install the triggering micro switch on the panel, system will work when pressing the triggering switch. It is especially helpful when you want to park the car inside of the garage without engaging reverse gear. System will stay on for 2 minutes. 7. Clean the area of the dashboard where the LCD display is going to be mounted. 8. Remove the sticker off the bottom of display. Also remove protective screen cover from LCD screen. 9. Mount the display on the dashboard by firmly pressing down the display. 10. Connect the display unit, and then connect all sensors one by one 1. Installation of the screen The screen stick on the panel Which suitable for the driver 2. Installation of detectors 1. The sensors 5 and 8 must be installed at Same level. 2. The distance between The ground and the sensors is about 50-65 cm, suggested 55 cm. 3. The sensors must be installed perpendicular to bumper & avoid attaching on the metal. 4. To ensure the best detect position, the sensors 5 & 8 must be installed beside the edge 30-40cm, suggested 30cm. 5. After measurement, make a symbol. 6. To ensure best detecting results, the sensors 1 & 4 must be installed near the edge 8-13cm, suggested 11cm. 7. Measuring the distance between sensors 1 & 4 and marking a (L) sign. 8. Marking the points of sensors 2 & 3 by 1/3 L. 9. Using the 20mm drill, drill through the point which is marked, secure the sensors into the holes. 3. Installation of main unit 1. The main unit must be installed in the trunk to avoid moisture & heat. 2. Lead out the power wire from the startup facility of the vehicle, connect it to the power supply wire of the main unit. 3. Plug the power supply wire, screen wire & sensors wire respectively to the inputs of the main unit family.