1980-2003 HARLEY DAVIDSON BARON TACHOMETER installation manual

0

Filed Under (Harley Davidson) by admin on 12-03-2012

download
1. Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off-center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating the tach internals, re-installing the bezel and retightening the set screw. 2. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, and then tighten the tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. 3. Route tach’s wire harness lead under dash for simplest and cleanest installation. 4. Make your wire connections as follows: a. Locate the pink wire under the speedo (sometimes has a plastic bullet end on it). Cut the plastic off and splice the pink wire with the green wire from the tachometer. b. Find the orange wire and attach the tach power wires to it (usually blue & red from tach (incandescent) or red & yellow for single color LED tachs. On 7-color LED models it is red from tach and red from LED controller box) . c. Locate a suitable ground (usually a bare frame bolt) and attach the black wires from the tachometer and the LED controller box (if equipped).

Incoming search terms:

LED Harley-Davidson Replacement Fog Lights Installation Manual

0

Filed Under (Harley Davidson) by admin on 08-03-2012

download
1. First remove the set screw located on the bottom of the trim ring that holds the fog light in. Carefully lift the fog light out of the motorcycle as you disconnect the wires. 2. Remove the inner retaining ring located behind the lighthead and discard or save it. This retaining ring will not be used in this installation. 3. Attach the foam gasket to the LED lighthead as shown, leaving a gap on the bottom for drainage. 4. Connect the wires of new lighthead to the existing motorcycle wires. RED = +12 Volts BLACK = Ground 5. Insert the lighthead into the mounting hole of the fog light and secure it by re-installing the trim ring. 6. Test the lightheads operation and installation is complete. IMPORTANT! Before returning this vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle components/equipment

HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

HARLEY DAVIDSON TOURING LAYBACK LICENSE PLATE MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
This kit fits all 1999 and later FLHR (Road King®) models, FLTR (Road Glide®) and FLHT (Electra Glide® standard) models having license plates measuring a maximum of 7-1/4 x 4-1/4 inches (184 x 108 mm). Also fits 2003 FLHRSEI2 (Screamin’ Eagle® Road King). Does not fit with Detachable Tour-Pak Rack, part number 53276-04. Does not fit 2002 FLHRSEI (Screamin’ Eagle Road King). Kit Contents See Figure 1. INSTALLATION 1. Remove the license plate from the vehicle (if installed). Remove the two hex head bolts holding the original equipment (O.E.) license-plate bracket in place. The bolts and license-plate bracket can be discarded. 2. See Figure 1. Install the new layback license plate holder (1) using the button-head hex socket screws (3) from the kit. Tighten the screws to 19 ft-lbs (25.8 Nm) . 4 1 3 7 5 2 6 is02737 1. License plate holder, layback 2. Foam pad (6) 3. Screw, button head, hex socket (2) 4. License plate frame 5. Set screw, socket head (2) 6. Hex key 7. Reflector assembly, Part Number 59365-07 Figure 1. Layback License Plate Mount Components 3. Position the license plate onto the foam pads (2) of the license plate holder, centering and aligning the plate parallel to the holder edges for best appearance. NOTE Slots in the inside top edge of the license plate frame (4) fit over the two tabs on the top edge of the license plate holder. 4. Hook the top of the license plate frame over the top edge of the holder. Swing the bottom edge of the frame inward, holding the license plate in position against the pads. 5. Use the hex key (6) from the kit to securely fasten the license plate frame to the holder with the two socket head set screws (5)

HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

Incoming search terms:

HARLEY DAVIDSON THERMOMETER/ CLOCK, HAND LEVER BRACKET CLAMP MOUNT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTE The figures show the gauge mounted to the clutch (left-hand) lever clamp. The gauge can be mounted on either the clutch or brake lever side, using the upper or lower clamp mounting screw per customer preference. 5 3 1 2 4 is01874 1. Gauge 2. Bracket (bent backward) 3. Socket head set screw from this kit 4. Original equipment screw 5. Original equipment washer (front of bracket) Figure 1. Gauge Bracket Mounted to Upper Screw (Left-Hand Shown) 1. See Figure 1 and Figure 2. Using a T27 TORX drive head, remove the desired screw (upper or lower) with flat washer securing the handlebar clamp to the hand lever bracket. NOTE When mounting the gauge bracket to the lower clamp mounting screw, install the original flat washer behind the bracket. 2. Install the handlebar clamp screw with flat washer through the larger hole in the gauge bracket, and tighten to 60-80 in-lbs (6,8-9,0 Nm). 3. Rotate the gauge to the desired angle, then tighten the gauge attaching screw securely. SETTING THE TIME ON THE CLOCK NOTE The clock is shipped with the stem pulled out, which stops clock operation. If the stem has been pushed in, pull out the stem carefully, and turn it until the hands indicate the correct time. Carefully push the stem back in to start the clock. REPLACING THE CLOCK BATTERY The clock battery (Type SR626SW) is a common type, available wherever watch batteries are sold. It is recommended that the battery be replaced at a watch repair facility, as the screw back cover requires a special tool for removal and replacement. The clock is waterproof, and requires special attention when re-assembled.

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

Baron Tachometer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Some models like Harley-Davidson, Kawasaki Vulcan FI models, Suzuki FI models, Honda VTX 1800 and others may require the included Tach Adapter. See separate instructions for installation of the adaptor. Wiring instructions for 7-Color LED Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire of tach to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire of tach to CHASSIS (Ground) • Red wire to of tach to POSITIVE terminal of coil (or other switched 12 volt source) • Red wire from control box to POSITIVE terminal of coil (or other switched 12 volt source) • Black wire from control box to CHASSIS (ground) • Control box plugs into tach with the 4-way connector • Button plugs into the control box. Button can be mounted on handlebar or any other convenient place Wiring instructions for White- or Black-Face Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire to CHASSIS (Ground) • Red wire to POSITIVE terminal of coil (or other switched 12 volt source) • Blue wire to POSITIVE terminal of coil (or other switched 12 volt source) General mounting instructions (1) Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off- center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating tach, re-installing bezel and retightening set screw. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, then tighten tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. (2) Route tach’s wire harness lead to coil as necessary for simplest and cleanest installation. Feed tach harness alongside bike’s wiring harness (passing behind any plastic frame covers), then downward toward coil. (3) Make your wire connections as recommended above. Use the spade and piggyback connectors

Incoming search terms:

KICKSTAND PAD – INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 23-12-2010

download
1. Slide the pad onto the kickstand being sure it is as far as it will go. 2. Tighten the setscrew on the side of the pad securely. 3. Recheck the pad and set screw occasionally to be sure that it is secure. Note; All kickstands are forged or stamped and then the mold parting line is hand ground. Some kickstands may have an excess amount of material on the bottom of the foot. If your pad does not slide completely onto the kickstand you will need to grind or file the bottom of your kickstand foot flat or flush until the pad does slip on completely.

Incoming search terms: