HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON SPORTSTER CHROME PRIMARY TRIM COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat and disconnect the negative battery cable at the engine crankcase. Retain all seat mounting hardware. 2. Models with mid foot controls: Remove the two screws retaining the left-side rider footrest and mounting bracket assembly. 3. All models: See Figure 1. Note the installed orientation of the transmission foot shift lever to aid in re-assembly. Use a 1/4 in. hex key to remove the socket head screw (5) holding the shift lever (3 or 4) to the transmission shift lever shaft (1). Remove the lever and rubber washer (2). 4 1 5 3 2 5 is 01929 1. Transmission shift lever shaft 2. Rubber washer 3. Foot shift lever (mid control) 4. Shift lever (forward control) 5. Socket head screw Figure 1. Shift Lever Removal 4 2 3 1 is 01930 Figure 2. Primary Cover Mounting Screw Locations NOTE Remove ONLY the four screws shown. 4. See Figure 2 and Figure 3. Remove and discard the primary cover hex-socket head screws from the four locations shown. 5. Refer to CLUTCH CONTROL: REMOVAL: CLUTCH CABLE-LOWER in the Service Manual to remove the clutch cable at the lower end with these exceptions: •The negative battery cable has already been disconnected, and •On mid-control models, the rider footrest has already been removed. 6. See CLUTCH LEVER AND CLUTCH CABLE-UPPER to remove the clutch cable at the upper end. NOTE Be careful not to scratch the paint on the frame tube when removing the clips. 7. Carefully remove the two vinyl-coated spring steel clips that retain the clutch cable to the frame downtube. 8. Obtain all of the items from the kit. 9. See Figure 2. Insert a chrome screw (3), from the outside, through the hole in location 3 on the chrome trim cover. Place the thinner steel spacer (4) onto the threads of the screw from the inside of the trim cover. 10. Use a 5/32 inch hex key on the screw head, and grip one of the Nylon keeper washers (6) with a pliers. Install the washer onto the screw until several threads extend from the washer, capturing the screw and spacer on the trim cover. 11. Insert the remaining chrome screws, from the outside, through the holes in locations 1, 2 and 4 on the chrome trim cover. Place a thicker steel spacer (5) onto the threads of each screw from the inside of the trim cover. 12. Thread a Nylon keeper washer onto each of the screws as described in Step 10. 13. Position the trim cover over the primary cover with the transmission shift lever shaft extending through the clearance hole (A) in the chrome trim cover. 14. Thread one of the chrome screws into the mating primary cover mounting hole for several threads, taking care not to cross-thread the screw in the hole. 15. Carefully start the remaining screws partially into their mating holes. Continue tightening the screws in turn

HARLEY DAVIDSON SPORTSTER FORWARD FOOT CONTROLS

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
LEFT (SHIFTER) SIDE 1. Remove stock footrest assembly and save footrest for reinstallation. Replace existing sockethead capscrews that attached footrest bracket to primary cover with washers (5) and shorter screws (21) from kit. 2. Remove stock shift lever and save shifter peg and mounting screw. 3. See Figure 1. Remove left side stock motor mount and save nuts, washers, and P-clamp for clutch cable. The bolts will be replaced. 4. Put Loctite 243 on threads of left side foot control support (15) and thread support into left side machine motor mount (11). Install C-clip (8) onto support where it exits the backside of machine motor mount to hold support in place. 5. Install left side motor mount assembly in place of stock motor mount using washers and nuts saved from step 3, and bolts (22 and 23) from kit. Tighten bolts to 25-30 ft-lbs (41-47 Nm). Make sure to reinstall the P-clamp and clutch cable in the same hole location they were removed from in step 3. 6. Install shift lever (14) from kit using stock fastener. 7. Put Loctite 243 on threads of clevis mounting screw (4) and install shift lever pedal (13), clevis (17), and footrest (stock), as shown. To install footrest, place a spring washer (19), along with the mount end of the footpeg, inside the slots of the clevis. Make sure the spring washer is positioned inside the clevis with the square edge towards the inside as shown in Figure 3. Secure footpeg and spring washer with bolt (2) and locknut (7). Tighten locknuts to 19 ft-lbs (26 Nm)

HARLEY DAVIDSON SOFTAIL EXTENDED REACH CONTROLS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
PREPARE THE MOTORCYCLE 1. For models equipped with saddlebags: Remove the saddlebags following the instructions in the appropriate Service Manual. 2. Remove the seat following the directions in the Owner’s Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect the negative battery cable. 4. Secure motorcycle in upright position. NOTE This kit is not compatible with engine guards. 5. If the engine guard is present, remove and discard it. LEFT SIDE Component Removal 1 3 4 2 7 5 6 8 2 is05048 1. Pretzel clip 2. Bushing (2) 3. Screw (6) 4. Jiffy stand bracket 5. Bumper 6. Jiffy stand leg 7. Clevis pin 8. Spring Figure 1. Jiffy Stand 1 2 3 5 4 is05053 1. Jam nut 2. Shifter rod end 3. Acorn nut 4. Shifter rod 5. Shifter arm Figure 2. Shifter Linkage 1. For HDI Vehicles: Remove the left side foot control support, and jiffy stand sensor, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. For all other models: Remove the left side foot control support, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. NOTE Two bearing sleeves will remain inside the footrest bracket. The extended controls bracket from the kit will include two sleeves pressed into the bore of the shift lever arm support. 2. Remove rod ends and jam nuts from the shifter rod. Save the rod ends and jam nuts for installation. Component Installation 1. See Figure 9. Select shifter mounting assembly (6), O- rings (5), nylon washer (4) and the shift rod (1) from the kit. 2. Install the shift arm and new O-rings in the bracket. 3. Apply LOCTITE 243 Threadlocker and Sealant to the three mounting screws and mount the shifter bracket with shift arm to the frame. Tighten the mounting screws to 25-30 ft-lbs (33.9-40.7 Nm)

Incoming search terms:

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

2008 KTM 125 SX, 144 SX, 250 SX OWNER'S MANUAL

0

Filed Under (KTM) by admin on 25-11-2010

download
Short circuit button (SX) The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open it: Press the release button [2] and turn the tank cap in a counterclockwise direction. To close it: Put the tank cap back on and turn in a clockwise direction until the release button snaps into place. Install tank breather hose [3] without kinks. Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. Choke knob When pulling the choke knob [4] fully towards the top, a bore is opened in the carburetor. Through this bore the engine can take in additional fuel. This results in a rich fuel-air mixture, that is needed for a cold start. When pressing the choke knob downward in the carburetor, the bore is closed again. ON OFF 4 1 2 3 ENGLISH 7 Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear. OPERATION INSTRUMENTS » Kickstarter The kickstarter is mounted on the left side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is disposed in front of the right foot rest. Its basic position can be adjusted to your seat position (see maintenance work). 1 N 2,3,4,5, (6) 2 3 1 Compression damping of fork Hydraulic compression damping determines the reaction when the fork is compressed. The degree of compression can be adjusted with adjusting screws at the bottom of the fork legs. Turn the screw [1] clockwise to increase damping, turn it counterclockwise to reduce damping during compression. STANDARD ADJUSTMENT: -turn adjusting screw clockwise as far as it will go -turn it back by as many clicks as are specified for the relevant type of fork Typ WP Suspension 14187D01 . . . . .14 clicks Typ WP Suspension 14187D03 . . . . .14 clicks

Yamaha V-Star Forward Control Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Brake Side 1. Locate the brake light switch and clip the wires 2″ from the switch. 2. Remove the banjo bolt from the rear caliper and remove the brake line being sure to capture all fluids in a sealable container for proper disposal. 3. Trace the brake line back toward the front and remove any brackets or zip-ties that hold it in place. 4. Remove the two bolts that hold the right side floorboard/control bracket to the frame and remove all the stock components, including the rear master cylinder and any linkage. 5. Install the new brake side control onto the stock location using supplied (10mm) bolts. 6. Install the new brake line with straight banjo adapter to rear caliper with the stock banjo bolt being sure to use a crush washer on both sides of the banjo fitting. Route the line back towards the front as the stock one was. 7. Connect the brake-line to the new reservoir/master cylinder with the supplied banjo bolt brake switch bolt making sure you have a crush washer on both sides of the banjo joint. 8. Connect the two wires from the switch to the stock wires that were clipped in step #1. Use the supplied connectors or solder them together. (This is a simple open/close switch so polarity does not matter) This switch operates by pressure so it will not work until the reservoir is filled and the brakes are bled. Shift Side 9. Loosen the two nuts on the shift linkage. Twist the linkage as necessary to remove it. 10. Remove the two bolts that hold on the left side floorboard/control and remove it from the bike. 11. Install the supplied rod end onto the new shift lever with the supplied (5/16) button head bolt. 12. Install the new shift side control onto the stock location using supplied (10mm) bolts. 13. Install the new rod end into the new shift rod, and the opposing end into your stock rod end, being careful to start both sides at the same time. Adjust to suit the rider and lock down with the nuts. Finishing Up 14. Unbolt master cylinder lid and fill reservoir with bike manufacturer’s recommended DOT brake fluid. (Remember to never reuse or mix old brake fluid and NEVER mix DOT 4 and DOT 5 together.) Bleed the brakes per your service manual. Check fluid level in reservoir periodically and fill as necessary to maintain full capacity of reservoir. 15. Make sure that the brake light is working when the brake is applied. 16. Ride and enjoy your new Supreme Legends Forward Controls! **Note** We strongly suggest that you use blue Loc-Tite # 242 on all fasteners except the banjo bolts to insure that they stay tight. Torque all bolts to factory specifications.

2003 Model Ural Gear Up, Patrol, Tourist Owners Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
19 Kick lever Is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift foot pedal Is a two-arm type. When the front arm is depressed, shifting from higher to lower gear takes place. When the rear arm is depressed, shifting from lower to higher gear takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift into a higher gear if you do not use your heel to shift, rather the ball of your foot. The neutral position is fixed between the 1st and 2nd gears. It is important to shift smoothly with a constant force and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pushed. IMPORTANT! The green pilot lamp will illuminate when either the transmission is in neutral or when the reverse gear is engaged (see “Starting the Engine”). Turn indicator pilot lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral and reverse gear engagement , indicates that the gearbox is either in neutral or in reverse. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles.