2008 KTM 65 SX 65 XC OWNER'S MANUAL

0

Filed Under (KTM) by admin on 09-03-2012

download
SERIAL NUMBER LOCATIONS » OPERATION INSTRUMENTS » Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number The engine number is stamped into the engine housing underneath the carburetor. Enter this number in the field on page no 1. Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handle bars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). 1 A 2 B
ENGLISH 7 OPERATION INSTRUMENTS » Short circuit button The short circuit button [1] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open it: turn filler cap counter-clockwise. To close it: put filler cap back on and tighten it by turning it clockwise. Install tank breather hose [2] without kinks. Fuel tap The fuel tap [3] is located on the left side of the tank. Opening the fuel tap: Turn the knob all the way to the left. Closing the fuel tap: Turn the knob all the way to the right. Choke The choke button [4] is located on the left side of the carburetor. Pulling the choke button all the way out opens a bore in the carburetor through which the engine can take in additional fuel, thus achieving the „rich” fuel air mixture needed for cold starting. Pushing the choke button back in closes the bore in the carburetor. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear

2007 KTM 250 SX-F 450 SX-F INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 06-02-2012

download
Clutch lever The clutch lever [1] is located on the left side of the handlebar. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hot start lever If you pull the red hot start lever [2] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a “lean” fuel-air mixture of the type needed for hot starts. 2 1 A Fuel tap OFF In this position the fuel tap is closed. No fuel can flow to the carburetor. ON During operation the twist grip must be turned to ON. This means that the fuel can flow to the carburetor. OPERATION INSTRUMENTS »
Starter button (450 SX-F) Pushing the black starter button [3] will actuate the E-starter. ENGLISH 6 Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. Filler cap To open the filler cap: Turn the filler cap 45 ° counter-clockwise. To close the filler cap: Put the filler cap on and turn it 45 ° clockwise. OFF ON 1 A 2 3 ENGLISH 7 OPERATION INSTRUMENTS » Choke If you pull the choke button [1] out as far as possible, a bore in the carburetor will be opened through which the engine may take in additional fuel. The result is a “fat” fuel-air mixture of the type needed for cold starts. To deactivate the choke, push the choke button back into its basic position. Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral is located between first and second gear. Kickstarter (250 SX-F) The kickstarter is mounted on the right side of the engine. Its upper part can be swivelled. Foot brake pedal The foot brake pedal is located in front of the right footrest. Its basic position can be adjusted to your seat position (see maintenance work). Plug in stand The plug-in stand can be attached to the wheel spindle on the left side of the motorcycle

Incoming search terms:

SUZUKI SV1000 ELECTRICAL SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COUPLER •With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. (C” -78-14) • * Bend the clamp properly so that the wire harness is clamped securely . • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . ELECTRICAL SYSTEM 7- 3 7-4 ELECTRICAL SYSTEM BATTERY •The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. • Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE HARNESS ROUTING” section. (CJ8-14)

Incoming search terms:

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms: