HONDA VTX 1800C,F BIG SHOTS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 09-11-2011

download
Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, locate and unplug connector(s). Remove wire tie (take note of harness routing for reassembly). Remove sensor(s) from exhaust system. Note: Use caution when handling. Do not handle sensor tip area, store in a safe dry place for reassembly. 3. Remove allen head screw, holding rear brake master cylinder reservoir and cover. 4. Remove footpeg flange head bolts. Carefully lower right foot peg assembly, with rear brake reservoir attached. Note: Use caution when handling brake line. 5. Remove exhaust port flange nuts.6. Remove flange bolts securing rear muffler mount to exhaust system mounting bar. 7. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). 8. Remove rectifier from mounting bar. 9. Remove stock (cast iron) exhaust system mounting bar

KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 23-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, remove passenger seat. Remove two bolts securing operator seat and set seat aside. Locate and unplug oxygen sensor connector from wiring harness (Figure 1).(Note wire routing for reassembly). 3. Remove right side floorboard assembly held in place by two bolts (Figure 2). 4. Remove exhaust port flange nuts. 5. Remove flange bolts securing rear muffler to exhaust system mounting bracket. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). Page 1of 4 K400IN Rev. 1.1 KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM Part #18311 Tools required for installations 6mm Allen wrench 8mm 12mm 14mm sockets 3/8″ Ratchet & Extensions 19mm Wrench 9/16 Wrench Brake bleeder & fluid
7. Check condition of stock exhaust gaskets. Replace if damaged or worn. 8. Remove plastic hose clamp securing rear brake hose to swingarm.Save for re-use. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loops in swingarm. 11. Remove three bolts holding stock exhaust mounting bracket and slide bracket off end of brake hose. 12. Slide brake hose through loop on new bracket (stamped 357-P) and install to the original mounting bracket location, using three 8mm x 16mm Allen bolts (supplied) (Figure 3). 13. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 14. Slide brake hose through loops on swingarm and reconnect brake hose to caliper. 15. Reinstall plastic clip onto swingarm. 16. Brake system must be bled or brake will not operate correctly.

Incoming search terms:

HARLEY DAVIDSON V-ROD Fi2000 Fuel Injection Module Installation Manual

0

Filed Under (Harley Davidson) by admin on 15-11-2010

download
1. Flip up seat, to gain access to radiator reservoir area. 2. Remove Dzus fastener to remove simulated fuel tank cover, over airbox housing. Depending on which model V-Rod is being worked on, the front shrouds covering the upper front frame section may also need to be removed. 3. Place Fi2000 in under-seat area, run fuel injector connector harness up right side frame rail between top right frame rail, and radiator overflow tank, see Figure 1. At the rear of the airbox, route the harness below the airbox, and downward next to the inner radiator hose. Unplug both stock fuel injector connectors, on the front and rear injectors between the engine cylinders, see Figure 2. These are disconnected, by depressing the metal springs that are on the end of each female connector. The stock female connectors are marked “F” and “R”, noting which connector goes to the front and rear injector, be sure to pay attention to this. Now connect the longer male Fi2000 connector to the front female H.D. connector. Plug shorter Fi2000 male connector into the stock rear female H.D. connector. Then plug the longer female Cobra connector onto the front stock H.D. injector. Plug the shorter Fi2000 female connector onto the rear injector. Each injector connector pair should rest underneath each respective injector. 4. It is now time to install the oxygen sensor eliminator modules. This product is designed to eliminate the “check engine” light from coming on when the stock oxygen sensors are disconnected on Harley Davidson Motorcycles utilizing fuel injection. The motorcycle has a full “open loop” fuel injection map written in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed or just disconnected. 5. Locate the rear oxygen sensor and follow the harness up to the under-seat area behind the radiator overflow tank. Pull the stock connectors up from below the overflow tank and disconnect, see Figure 1. Plug one of the supplied Oxygen sensor eliminators on to the stock male connector. Tuck the connectors back underneath the bracket behind the radiator overflow tank. 6. Now locate the front oxygen sensor on the front headpipe, and trace the oxygen sensor harness back to the connectors tucked between the left front frame rail and plastic radiator shroud, see Figure 3. Pull these connectors out, and disconnect them. Plug the remaining supplied oxygen sensor eliminator on to the stock male connector. Tuck the connectors back in between the frame rail and plastic shroud

Kawasaki ZX6R/ RR 2003-2004 Frame Slider Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Locate and remove right engine stud. Tip: Both main engine studs on the ZX6R tend to be very tight from the factory, use a stubby socket to remove stud. Make sure you have good engagement or the head of the bolt can strip. 2. Mount Right side frame slider using 99-HB-SH101250110 Socket Cap 10 X 1.25 X 110 Main Engine Stud and torque down to OEM torque specs. 3. Remove the left side OEM motor mount bolt. 4. Using the 10 X 1.25 X 110 Bolt supplied in the kit: Use the 99-SP-750-4200-L Left Side Bell Type Spacer Black Anodized 5. The small end of the (99-SP-750-4200-L Left Side Bell Type Spacer Black Anodized) goes against the left side of the frame. The longer of the two frame sliders goes on top of the spacer. Using the 10 X 1.25 X 110 Socket Cap mount and torque down to OEM specs