HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

Motorcycle Hand Warmer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Disconnect the Positive (+) terminal from the battery. 2. Remove the existing grip from the Clutch side. Removing the grip may require blowing compressed air in the end between the grip and the bar, injecting brake cleaner fluid, or cutting it off. 3. Clean the handlebar where the grip was removed with alcohol or a solvent to remove all residue and dry with a clean cloth. 4. Determine where the Clutch side heater will be mounted. Take the heater marked “Clutch” and place it on the handlebar approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 9:00 o’clock or they can be positioned on the bottom for appearance. Peel off the release paper and adhere the heater to the handlebar with the wires toward the headlight. 5. Apply a high temperature adhesive (such as JB Weld) to the inside of the Clutch side grip. Install the grips over the heaters and let the adhesive cure as instructed by the adhesive manufacturer. 6. The Throttle side heater is installed on the throttle sleeve under the rubber cover. Remove the rubber cover that is installed over the throttle sleeve so the Throttle side heater can be applied. Some of the throttle sleeves have ribs which need to be cut or ground off so the heater can make full contact with the sleeve surface or it will over heat in the void areas. 7. Determine where the throttle side heater will be mounted. Take the heater marked “Throttle” and place it on the throttle sleeve approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 3:00 o’clock with a loop to allow for the twisting motion of the throttle. Peel off the release paper and adhere the heater to the throttle sleeve with the wires toward the headlight. 8. Apply a thin coat of adhesive (such as J.B. Weld) to the surface of heater only and reroll the rubber hand grip over the entire throttle sleeve. Wipe off any excessive adhesive that may have rolled out

Incoming search terms: