HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

HARLEY DAVIDSON SPORTSTER CHOPPED FENDER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION Preparation 1. Position the vehicle on a motorcycle lift under the frame so the vehicle is upright and level. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 3. Remove the battery from the vehicle per the instructions in the service manual. 4. Raise the rear of the vehicle to relieve the load on the shock absorbers. 5. Follow the service manual instructions to remove only the bottom end shock absorber fasteners on each side of the vehicle. Save the fasteners for later assembly. 6. Raise the rear of the vehicle further to allow access to the underside of the rear fender. 7. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. Rear Fender Removal NOTE Note the location and orientation of rear fender mounting hardware, and save for later assembly. 1. Refer to the service manual and follow the instructions given to remove the rear fender, with the following exceptions: a. Removal of the tail lamp from the fender is not necessary. Rear Lamp Wiring 1. Cut off and discard the socket housings and terminal ends from the turn signal wires. 2. See Figure 1. Unscrew and remove the turn signal stalk (15) from one of the turn signal lamps, and discard. Remove and retain the turn signal lamp and support (14) from the rear fender support cover. 3. Insert the blade of a small screwdriver into the slot at the bottom of the turn signal lamp lens (2), and twist to unsnap the lens from the housing (1)

HARLEY DAVIDSON LIGHTED CHROME DIRECTIONAL BAR INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle. Save all hardware for reattachment. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 1 2 3 4 is02199 1. Ground wire 2. Hold lamp in place 3. Backing plate 4. Self-tapping screw Figure 1. Remove Backing Plate 4. See Figure 1. For each end of new directional bar, remove self-tapping screw that holds corner of backing plate and ground wire in place and remove backing plate. 1 2 is 02200 1. Hold lamp in place with this screw 2. Turn signal connector(s) are behind LED Figure 2. Assembling Directional Bar 5. See Figure 2. For each end of bar, place turn signal lamp in position with wires routed as shown. Move LED light out of the way and thread 5/32 inch Allen socket screw into lamp to hold lamp in place. Tighten screw.

HARLEY DAVIDSON VRSCF RIGID SADDLEBAGS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Kit Contents See Figure 5 and Table 1. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the rider seat and passenger pillion per the instructions in the service manual. 3. See Figure 1. Remove the four rear fender mounting bolts (1) and washers (2), and the passenger grab strap (3). If necessary, move the ECM to better access the fender mounting bolts. 1 3 2 is05463a 1. Bolt (4) 2. Washer (4) 3. Grab strap Figure 1. Fender Mounting Bolts 4. Disconnect the six-way tail lamp socket housing and four- way turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness. 5. If a luggage rack, sissy bar upright or both have been mounted on the rear fender , remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. NOTE The rack and/or upright will remain attached to the rear fender when the fender is removed. 6. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure 2. Remove the two bolts (8) holding the side license-plate bracket (1) to the seat pan (9). c. Remove the license-plate adjuster bracket (2) carriage bolt (3), washer (4) and lock nut (5), and the license- plate illuminator (6) and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (1), screws (7) and bolts (8) can be discarded. Set the remaining items aside for installation to the new side license-plate bracket. 8. Remove and discard the rear side reflectors (10). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. NOTE Access to the shock absorber adjustment collar is more difficult with the saddlebags in place. 9. Adjust the rear suspension preload, if desired, per the instructions in the service manual

HARLEY DAVIDSON NARROW CHROME DIRECTIONAL BAR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
This kit is designed for installation on 1986 and later FLST®, FLSTC®, FLSTN®and 1991 and later Touring models. (Except 2004 and later FLHRS®and FLTR®) NOTE: Will not fit when equipped with Flat Lens Turn Signal Module (Part Number 91699-99A). Installation 1. Disconnect turn signal wires. For 1999 and later models: See Figure 1. Remove taillight cover and disconnect turn signal wires at connectors shown in illustration. For 1998 and earlier models: Disconnect turn signal wires at connectors located in directional bar. On 1994 and later models there are two wires for each turn signal lamp. Earlier models have only 1 wire per lamp. 2. Remove existing directional bar from motorcycle and save hardware for re-installation. If the turn signal connector is too large to be removed from the directional bar, remove the wires from the connector as follows: Bend back the connector latches on the sides of the connector slightly to free the secondary lock. Rotate the secondary lock outward on hinge to access terminals in chambers of connector housing. With a paper clip sharpened to a chisel point, insert the paper clip into the connector housing cavity until it stops. Pivot the end of the paper clip and gently tug on the wire to pull the terminal from the cavity. Do not tug on the wire until the tang that holds the terminal in the cavity is released. Take your time, a few tries may be required before you develop a feel for releasing the terminal from the connector. 3. Remove screws that mount turn signals lamps to existing directional bar. Remove lamps and turn signal wires (with their attached connector halves) from existing bar. 4. Position directional bar in mounting location at rear fender and secure bar to motorcycle using original hardware removed in step 2. Route turn signal wires from motorcycle back into directional bar, or up to taillamp (if 1999 and later model) and mate connectors. If the wires were removed from the connector in step 2, insert the terminal ends of the wires into the connector until they snap in place, then mate connector halves.