HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

HARLEY DAVIDSON CLEAR/SMOKED BULLET STYLE OR VRSC TURN SIGNAL LENS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson Dealer. 1. See Figure 1. Locate the removal notch on the turn signal lens and carefully pry from housing. Discard lens. Repeat for remaining lenses. 2. Remove bulbs from turn signal assemblies. 3. Obtain new amber bulbs from kit. Install the bulbs marked 1157A (Dual Filament) to the front turn signal assemblies. Install the bulbs marked 1156 (Single Filament) to the rear turn signal assemblies. NOTE See Figure 1. VRSC (V-Rod) Models have unique rear turn signal lenses. The rear lens is identified with a dimple mark in the center of lens. The front has no dimple. 4. Obtain new lens from kit and install by snapping into place. Check turn signals for proper operation. ® Figure 1. “Bullet” and VRSC Turn Signal Lenses Kit Numbers 69303-02, 69304-02, 69309-02 and 69315-02 Service Parts Clear/Smoked “Bullet” and VRSC Lens Kits Date 5/02 Part No. 69303-02 and Others Item Description Part Number Kit Number 69303-02 1 Clear lens, bullet, front and rear (4) 69324-02 Kit Number 69304-02 2 Smoked lens, bullet, front and rear (4) 69325-02 3 Bulb, amber (front) 69331-02 4 Bulb, amber (rear) 69330-02 Item Description Part Number Kit Number 69309-02 1 Clear lens, VRSC, front (2) 69324-02 5 Clear lens, VRSC, rear (2) 69322-02 Kit Number 69315-02 2 Smoked lens, VRSC, front (2) 69325-02 6 Smoked lens, VRSC, rear (2) 69323-02 3 Bulb, amber (front) 69331-02 4 Bulb, amber (rear

Incoming search terms:

HARLEY DAVIDSON CLEAR/ SMOKED DOMED OR FLAT TURN SIGNAL LENS KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
CLEAR/SMOKED DOMED OR FLAT TURN SIGNAL LENS KITS Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson Dealer. 1. See Figure 1. Remove existing turn signal lenses and discard. Retain lens mounting screws for installation. 2. Remove bulbs from turn signal assemblies. 3. Obtain new amber bulbs from kit. Install bulbs marked 1157A (Dual Filament) to the front turn signal assem- blies. Install bulbs marked 1156 (Single Filament) to the rear turn signal assemblies. 4. Refer to Figure 1. Using screws saved during removal, install the new turn signal lenses to front and rear turn signal assemblies. 5. Check turn signals for proper operation

Incoming search terms: