YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

HONDA GL1800 Windshield Panel Light Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
Note: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Remove the following per manual instructions. A. Rear view Mirror (Figure 1) -Remove the meter panel. -Remove the trim clip, screw and mirror cover. -Remove the three screws, bracket and mirror. -Disconnect the turn signal light 3P connector. B. Windshield Garnish (Figure 2) -Remove the left and right rearview mirrors per above instructions. -Remove the two bolts, washers and mounting rubbers. -Release the four bosses from the grommets and remove the windshield garnish. 3. Line up the windshield panel light in the windshield vent opening as shown in figure 3. Mark spots for final application. 4. Remove tape backing and carefully apply light at pre-marked spots. 5. Splice wires to mirror light as follows: a. Black to Ground b. Red to Orange/white wire to left mirror. 6. Reassemble all parts removed

HARLEY DAVIDSON THROWOVER SADDLEBAGS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Installation 1. Place the saddlebags on the vehicle so the straps are positioned over the top of the passenger seat. 2. Lace saddlebags together. 3. Adjust the leather straps so the saddlebags ride high and fit snugly and evenly against the side of the seat. Top of saddlebags may be replaced to achieve snug fit. NOTE On some models, the rear turn signal lights may interfere with mounting of saddlebags. To correct this, a new directional set-back kit is available under part number 90504-82. This kit allows the rear signal lights to be mounted in the rear positions on the fender support, on 1982 and later FXR and XL models. Contact your Harley- Davidson Dealer to obtain this kit. If rear turn signal lights interfere with saddlebags, see your Harley-Davidson Dealer for a turn signal set-back kit. Proper turn signal operation and visibility is a major concern for motorcyclists. Failure to have visible, operational rear turn signals may result in death or serious injury. 4. The front securing straps must be fastened to a point on the motorcycle which is forward of the saddlebags, such as the upper shock mount or fender brace. Be certain the straps so not interfere with any moving parts. Improper positioning or fastening of these saddlebags could cause them to interfere with the operation of the vehicle, possibly causing a hazardous condition. The fastening straps and the saddlebags must be clear of the rear wheel, drive chain or belt, sprocket and rear brake components. Location of the saddlebags should not interfere with the operation of the swingarm and rear shocks and the turn signals should remain clearly visible from the rear and side of the vehicle. Improperly positioned or fastened saddlebags could interfere with the operation of the motorcycle, which could result in death or serious injury. 5. The rear securing straps must be fastened to a point which is rearward of the saddlebags such as the rear turn signal light support. 6. Check that saddlebags are mounted with ample clearance between the bags and the brake caliper and disc so they do not contact each other, even when the swingarm deflects under full load. 7. Once both saddlebags are mounted correctly, check all securing straps to be certain they are not interfering with or exposed to any moving parts. Tuck the tails of the leather straps underneath the portion of the straps that connect the two saddlebags. NOTE On some motorcycles, it will be necessary to mount the saddlebags over the outside surface of the rear shock. This is acceptable if all CAUTIONS and WARNINGS are observed

Incoming search terms:

HONDA GL1800 CHROME MIRROR HOUSINGS INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
NOTE: Read instructions thoroughly before installing. USE SCREWS PROVIDED WHEN REASSEMBLING. 1. Place bike on center stand. 2. Remove the screw and mirror from the rearview mirror housing. Figure 1 3. Remove rearview mirror: Figure 2 a. Remove the mirror boot from the front fairing. b. Remove the trim clip, screw and mirror cover. c. Remove the three screws, bracket and mirror. d. Disconnect the turn signal light 3P connector. 4. Remove the three screws holding the directional light in the housing. Remove the turnsignal. Figure 3 5. Install new chrome housing using the screws provided and install parts in reverse order

Yamaha XV 1300 V star XVS13AW OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 04-12-2010

download
1. Front turn signal/position lights (page 6-34) 2. Headlight (page 6-32) 3. Seat lock (page 3-11) 4. Fuel injection system fuse (page 6-30) 5. Fuse box (page 6-30) 6. Main fuse (page 6-30) 7. Helmet holder (page 3-12) 8. License plate light (page 6-35) 9. Rear turn signal light (page 6-34) 10.Engine oil level check window (page 6-11) 11.Shift pedal (page 3-8) 12.Engine oil filler cap (page 6-11) DESCRIPTION 2-2 2 EAU10420 Right view 1. Tail/brake light (page 6-33) 2. Rear brake fluid reservoir (page 6-22) 3. Owner’s tool kit (page 6-1) 4. Battery (page 6-29) 5. Air filter element (page 6-15) 6. Fuel tank cap (page 3-9) 7. Front brake fluid reservoir (page 6-22) 8. Brake pedal (page 3-9) 9. Engine oil filter cartridge (page 6-11) 10.Engine oil drain bolt (page 6-11) 11.Coolant reservoir (page 6-14) 12.Shock absorber assembly spring preload adjusting ring (page 3-12) DESCRIPTION 2-3 2 EAU10430 Controls and instruments 1. Clutch lever (page 3-8) 2. Left handlebar switches (page 3-6) 3. Multi-function meter unit (page 3-3) 4. Main switch/steering lock (page 3-1) 5. Right handlebar switches (page 3-6) 6. Throttle grip (page 6-16) 7. Brake lever (page 3-8) INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key.

Incoming search terms:

YAMAHA XVS 650AK Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 18-11-2010

download
Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,450 mm (96.5 in) 930 mm (36.6 in) 1,105 mm (43.5 in) 710 mm (28.0 in) 1,625 mm (64.0 in) 145 mm (57.1 in) 3,400 mm (133.9 in) Basic weight: With oil and a full fuel tank 247 kg (544.5 lb) Bulb wattage quantity: Headlight Tail/brake light Front turn signal/position light Rear turn signal light Meter light Neutral indicator light High beam indicator light Turn indicator light Engine indicator light 12 V 60 W/55 W 1 12 V 8 W/27 W 1 12 V 27 W/8 W 2 12 V 27 W 2 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 12 V 1.7 W 1 ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in)

KYMCO MXU 300/ 250 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
FRAMES ERIAL NUMBER The frames erial number is stamped on the front oft he frame. (1) Frame serial number (2) Engine serial number 11 (1) (2) (01) Rear brake lever (03) Front brake lever (04) Right front turn signal light (02) Headlights/Position lights (05) Steering handlebar lock (06) Left front turn signal light 12 PARTS LOCATION (01) (02) (02) (03) (04) (05) (06) (07) Right rear turn signal light (08) Ta illights/Stoplights (11) Exhaust system (12) Trailer hitch (13) License light (14) Battery (09) Instrument and indicators (10) Left rear turn signal light (09) (08) (08) (10) (07) 13 (14) (13) (11) (12) 14 (15) Drive select lever Tool kit (19) Reservoir water tank (20) Brake pedal fluid reservoir (16) Fuel valve (17) Seat (18) (16) (15) (18) (17) (19) (20) 15 (21) ) Choke knob (23) Recoil starter Exhaust system (22 (23) (22) (21) (24) Front brake lever ) Front cargo rack (26) Front brake fluid reservoir (27) Ignition switch (28) Rear (29) Accessory socket seat (30) Rear brake lever (31) (32) Leftfootpeg /Parking brake (25 brake fluid reservoir Headlight dimmer switch Starter button Hazard switch Turn signal switch Horn switch (33) Fuel fill cap (34) Throttle lever (35) Rightfootpeg (36) Rear brake pedal 16 (33) (34) (32) (31) (35) (36) (24) (25) (26) (27) (28) (29) (30) NOTE: Themachineyou have purchased may differ slightly from those shown in the figures of this manual. (37) Rear cargo rack ) Flagpole bracket (38

Incoming search terms:

Incoming search terms: