1988-2000 Honda Goldwing GL 1500 Signal Mirror Installation Instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
Start on either the left or right side mirror. These instructions start with the right side mirror. Pull back the rubber boot covering the mirror mount. 1 2 3 Remove the accessory compartment cover. Remove the four screws on all sides of the accessory compartment. Remove the accessory compartment from the motorcycle fairing and set it aside. 4 The motorcycle’s electrical wiring for turn indicators is located forward of the accessory compartment cavity and behind the front amber turn indicator light. Disconnect the wire connected to the turn indicator light. 5 There are three screws holding the mirror housing to the mirror mount. Remove the three screws. Set the mirror housing aside.
Mirror Replacement – 2 – Remove the three screws holding the hinge to the mirror housing. Remove the hinge and remove the rubber boot surrounding the mirror housing. 1 Match the base of the hinge up to the new Signal® mirror housing. Mark the place on the hinge where the Signal® mirror wire will go through. Drill a ¼” hole in the hinge. 2 Position the rubber boot over the Signal® mirror housing. 3 Guide the Signal® mirror wire harness through the drilled hole in the hinge. Mount the hinge on the Signal® mirror housing using the original three screws.

Incoming search terms:

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms:

1999-2005 BMW K1200LT Motorcycle Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror by inserting the pry bar as shown. Slowly twist the pry bar to disengage the mirror. NOTE: Insert the pry bar as close to the mirror mount as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. 2. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 3. Once you have the mirror housing removed, route the Signal® mirror wire harness through the hole in the housing. Note: Leave about 6″ of slack, on the wire, for adjustment later on. 4. Use a screwdriver and remove the screw from the front turn indicator lens. 5. Disengage the lens and remove the light bulb as shown. 6. Route the Signal® mirror wire harness through the top opening in (A) and out the bottom opening in (B).

Incoming search terms: