HARLEY DAVIDSON ADJURE'S BIG CITY LED LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 20-04-2012

download
ADJURE OFFERS DOT COMPLIANT LED REPLACEMENT TURN SIGNALS TO FIT BOTH THE FLAT AND FOOTBALL HARLEY DAVIDSON TURN SIGNAL HOUSINGS. STOCK HARLEY DAVIDSON HAS 3-WIRE AMBER (RUN/TURN) IN FRONT AND 2-WIRE AMBER (TURN ONLY) IN THE REAR. IF YOU WANT TO CHANGE YOUR REAR TURN SIGNALS INTO RUN/TURN/BRAKE, YOU MUST CHANGE THE LENS COLOR TO RED AND THE BEST WAY TO DO THIS IS TO ALSO ORDER AND INSTALL OUR P/N# K48590 (RUN/TURN/BRAKE CONTROLLER). NOTE: WHEN USING LED’S AS A TURN SIGNAL YOU MUST ALLWAYS USE A “LOAD EQUALIZER” P/N#K48100 TO MAKE THEM WORK PROPERLY. INSTALLATION: COVERS BOTH FLAT AND FOOTBALL HOUSINGS 1) REMOVE THE LENSES FROM YOUR STOCK TURN SIGNALS BY REMOVING THE 2 SCREWS ON EACH SIDE OF THE LENS. 2) REMOVE THE BULB BY PUSHING IN AND TURNING COUNTER CLOCKWISE. 3) INSERT INTO THE LIGHT SOCKET THE PLUG ON YOU NEW LED’S BY PUSHING IT IN AND TURNING IT CLOCKWISE. 4) SET THE LENS ON THE HOUSING AND REPLACE THE SCREWS. TO CONNECT THE LOAD EQUALIZER: 1) THERE ARE 3 WIRES CONNECT THE BLACK TO A GOOD GROUND AND ONE OF THE WIRES TO ANYWHERE IN THE LEFT SIDE TURN SIGNAL SYSTEM AND THE OTHER WIRE TO ANYWHERE IN THE RIGHT SIDE TURN SIGNAL SYSTEM.

YAMAHA DT125RE/ X SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
OIL WARNING LIGHT CHECKING METHOD Main Switch “ON” Gears in “NEUTRAL” Oil warning indicator light does not come on Refeer to CHAPTER 8 “SIGNAL SYSTEM” Oil warning indicator light come on Shift into gear Oil warning indicator light does not come on Oil warning indicator light come on Supply engine oil Engine oil level and electrical circuit are OK 1 CHK ADJ TRANSMISSION OIL LEVEL INSPECTION/ TRANSMISSION OIL REPLACEMENT 3-11 TRANSMISSION OIL LEVEL INSPECTION 1. Inspect: •transmission oil level Oil level low **Add sufficient oil ******************************** Transmission oil level steps: •Place the machine on a level surface. •Warm up the engine for several minutes and stop it. •Visually check the oil level through the level window *. NOTE: •Check the oil level just one minute after stopping the engine. •The oil should e confirmed between maximum *and minimum *marks. •If the oil level is lower, add sufficient oil to raise it to the proper level. •Do not add any chemical additives. Transmission oil also lubricates the clutch and additives could cause clutch slippage. •Be sure no foreign material enters the crankcase. **************** **************** TRANSMISSION OIL REPLACEMENT 1. Warm up the engine for several minutes. 2. Place a container under the engine. 3. Remove: •oil filler cap * •drain pulg * drain transmission oil. NOTE: Drain the transmission oil with the motorcycle slightly inclined to the right. 4. Inspect: •gasket (Drain plug) •O-Ring (oil filter cap) Damage **Replace

BMW Motorcycles K-Models Maintenance Schedule

0

Filed Under (BMW) by admin on 12-11-2010

download
Check operation of sidestand switch (angle); orretracting sidestand linkage (K75′s) Apply silicone sprayto guide rods of adjustable windshield (onlyK1100LT, K75RT) Check torque at the bolts and nuts: • engine to frame • suspension strut mounts • side&centerstand pivot • rearwheel studs • front axle studs, clamp bolts, brake calipermounting bolts Final Inspection with Safety/ Operating check: • Condition of tires and wheels • Lights, horn, and signal system • Telltale and warning lights • Clutch and gearshift • Steering, hand & footbrake, ABS • Instruments (including optional accessories, radio, etc.) • Check &adjust engine idle speed • Check and adjust CO content of exhuast (models with closed loop catclyic con verters • Test ride, visual qualitycheck