2004 or later Harley Davidson Speedometer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Speed Sensor Installation: The microSpeed™ speedometer can be used with either +12V or +5V hall effect electronic sensors located in transmission. Sensor is not include. If your sensor operates on +5V DC wire speedometer to sensor and power as shown in Figure 2 below. Please note that color of wires from the sensor may vary, check sensor documentation for proper signal connections. For +12V sensor you will not need the Blue wire of the microSpeed™ speedometer. It may be cut short, but make sure that the end is properly protected so that it will not accidentally short to metal on the motorcycle. Use Figure 3 below for wiring a +12V sensor. H-D motorcycles 1999 and earlier used +12V sensors. H-D motorcycles 2000 and later use +5V sensors. Note: H-D OEM sensors require 20Kohm resistor(provided) between Sensor power and Sensor signal as shown. Procedure: 1. Locate wires and determine connection points. Cut wires and techflex to proper lengths. 2. Connect speedometer wires to proper signal wires as shown in diagrams, including 20K ohm resistor if using stock H-D sensor. Use either butt connectors provided or customer supplied connectors. 3. Use electrical tape or Heat Shrink tubing around sensor signal wire, sensor power, and resistor to protect resistor. 4. Proceed to Setup Section below. Setup microSpeed™ Speedometer: 1. Before proceeding review User Guide document for detailed instructions on following procedure. 2. Turn on power to speedometer, display should read “odo” 3. Set initial odometer value 4. Turn off power for 2 seconds; then turn power on again 5. Display should read “F 0″ 6. Enter Configuration and Calibration and set speedometer to proper operating mode. a. Harley English b. Harley Metric c. Standard speed sensor English d. Standard speed sensor Metric 7. Set Fuel miles per tank 8. Set Oil change interval 9. Set Speed adjustment 10. Confirm. 11. Test speed is reporting properly and adjust is necessary

HARLEY-DAVIDSON SPORTSTER MODEL'S 215 and S 215 INSTALLATION and CLEANING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1. Refer to Figures 1 & 2. 2. Remove taillight and remove seat. SAFETY: DISCONNECT BATTERY PRIOR TO ALL WIRING MODIFICATIONS 3. Disconnect Right turn signal connector inside taillight. Pull wire from the underside of fender. Cut the wire approximately 2 inches from the connector, 02/16/09 save for reinstallation. Ensure the wires are loose from all retaining clips under fender. 4. Remove nut located behind fender holding the turn signal. 5. On the right side only, Remove the two torx bolts from fender strut, carefully pull and rotate fender strut cover to remove. Pull turn signal wire completely out. Remove bolt holding turn signal to the fender strut cover. SADDLEBAG INSTALLATION 6. Reinstall the fender strut cover using the 1 7/8″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the front hole and the 1 1/2″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the rear hole. Refer to view “B”. Insert the chrome caps into the existing turn signal holes. Bend tabs over to ensure a snug fit. 7. Repeat disassembly and installation on opposite side. TURN SIGNAL RELOCATION 8. Install turn signal bracket between license plate and license plate bracket with ears of bracket facing the front of the motorcycle, using 1/4 – 20 x 3/4 Hex cap screws, 1/4 flat washers, and 1/4 – 20 locknuts. 9. Mount turn signals directly to bracket using 5/16 – 18 x 3/4 hex cap screws with a Black Plastic Spacer, and 5/16 star washer. For a clean installation slide rubber grommet over the wire and secure into hole in turn signal, remove top center mounting bolt on license plate bracket and run wires through this hole. Splice the connector back on the wire, and reconnect to wire harness. Ensure all wires are secure under fender. Reinstall taillight. 10. Connect battery and test turn signals for function. Information: Bags will be easier to mount and remove if a small amount of silicone lubrication is applied to rubber mounting points. 11. Mount saddlebags over spools on fender strut and secure with clips retained inside bags. 12. Inspect each clip to verify each clip is properly seated in retaining groove. See View “A”

HARLEY DAVIDSON CUSTOM TOURING FRONT BULLET TURN SIGNAL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION Outer Fairing/Windshield and Auxiliary Lamp Bracket Removal To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2 3 1 2 is 01215 1. Six-position connector 2. Four-position connector 3. Auxiliary lamp connector Figure 1. Disconnect Signal and Auxiliary Lamp 1. Remove Maxi-Fuse. Refer to SYSTEM FUSES, MAXI- FUSE in Service Manual. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 2. Remove the windshield and outer fairing. Refer to UPPER FAIRING/WINDSHIELD in Service Manual for the outer fairing/windshield removal procedure. 3. Disconnect auxiliary lamp and turn signal connectors. NOTE See Figure 1. On 2005 and prior year models, the left and right turn signals plug into a 6-place connector located on the left fairing support brace. On 2006 and later models, each turn signal plugs into its own 4-place connector located toward the bottom of the inner fairing on each side. 4. Using a T40 Torx® drive head, remove and save the four bolts securing the auxiliary head lamp bracket to the chassis. 5. Remove auxiliary lamp bracket from motorcycle. Turn Signal Assembly 1 is 01217 1. Triangular opening Figure 2. Insertion of Terminals Through Triangular Opening 1. See Figure 2. Insert wire terminals through the triangular opening in the turn signal mounting bracket included in the kit. 2. Fit turn signal housing onto bracket. 3. Apply a small amount of Loctite (243) blue (99642-97) to threads of hex head cap screw. 4. Tighten cap screw to 15-20 ft-lbs (20-27 Nm) . -J03753 1 of 2 Turn Signal Installation 1 is 01218 1. Turn signal wire Figure 3. Turn Signal Wire Routing 1. See Figure 3. Insert turn signal connector and wiring between bottom of fairing and top of outer fairing skirt. 2. Route turn signal wire under cutout on mounting bracket and place bracket onto motorcycle. NOTE Care must be taken so the turn signal wire is not pinched between turn signal bracket and motorcycle chassis. 3. Install washers onto turn signal bracket mounting bolts and apply Loctite 243 (blue) (99642-97) to the bolt threads. 4. Tighten mounting bolts to 15-20 ft-lbs (20-27 Nm) . 5. Route turn signal leads toward harness connector. Secure loose wiring with tie straps so wires do not rub against any sharp objects

HARLEY DAVIDSON SOFTAIL TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 2. Raise the motorcycle on a floor jack to lower the rear wheel for fender hardware access. 3. See Figure 1. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 1. Remove Tail Lamp Lens 4. See Figure 2. Using a Terminal Pick Tool (1), press locking tabs and disconnect turn signal connectors (2-place, Items 2 and 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. NOTE FXST/S/B tail lamp and connectors are positioned 180° from orientation shown in Figure 2. 6. Reach under fender to locate clips fastening turn signal wires in place. Carefully pull wires out of clips, and pull turn signal connectors and wires out from under fender. a. Remove two-inch (51 mm) section of conduit 4 inches (102 mm) from turn signal connectors. b. Cut black turn signal wire about 5-1/2 inches (140 mm) from its connector. c. Cut violet/brown turn signal wire about 4-1/2 inches (114 mm) from its connector. d. Save cut wires with respective turn signal connectors. 7. Remove the sissy bar and/or sideplate assembly, if equipped

HARLEY DAVIDSON XL DOCKING HARDWARE/ DIRECTIONAL RELOCATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION 1. See Figure 2. Following directions supplied with saddlebags to relocate rear turn signals, but also use the following exceptions to install the parts contained in this kit: •Use turn signal studs (4) in place of hex bolts supplied with saddlebags. The longer studs are required to accommodate the rear docking points. •On each side, insert relocation pad plate (3), saddlebag mount spacer (12), rear docking point (2), and docking point spacer (11) between relocation pad (supplied with saddlebags), and fender support cover as shown. •Use 4-inch long cap screw (5) in place of hex bolts supplied with saddlebags. The longer cap screws are required to accommodate the rear docking points. •The turn signal wires should be routed under the fender support cover back to the connectors they were removed from following the directions supplied with saddlebags. 7 1 14 2 12 6 9 3 1 11 4 10 8 16 17 15 18 5 13 is03490a 1. Locknut, 5/16-18 inch (3) 2. Rear docking point 3. Relocation pad plate from saddlebag kit 4. Turn signal stud 5. Cap screw, 5/16-18 x 4 inch 6. Spacer from saddlebag kit 7. Turn signal wire 8. Fender support cover 9. Cap screw, 5/16-18 x 2-1/4 inch 10. Front docking point 11. Docking point spacer 12. Saddlebag spacer 13. Washer, 1/4 inch 14. Locknut 1/4-20 inch 15. Cap screw, 1/2-13 x 3-3/4 inch 16. Spacer 17. Saddlebag support 18. Stock washer Figure 1. Installation shown on 2000 model On 1999 and earlier models: See Figure 2. Before mounting saddlebag supports, remove acorn nut from upper shock mount, and install washer (7), and shock mount spacer (8) as shown. Tighten upper shock mount spacer to 21-35 ft-lbs (28-47 Nm). This will properly space out the saddlebags to accommodate the docking points. On 2000 models: See Figure 1. Before mounting saddlebag supports remove button screw from upper stock mounts, and proceed to Step 2.

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

TRIUMPH AMERICA AND SPEEDMASTER FRONT TURN SIGNAL RELOCATORS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Remove the front turn signals as follows. The turn signal wire plugs are located inside the handlebar switch housings. Remove the two Phillips screws located on the forward facing side of the switch housing, remove the covers, unplug the turn signals and reassemble the switch housings. Unbolt the signals from their black mounting brackets, remove the brackets from the bottom side of the switch housings, reinstall the nuts and tighten securely. 2. Disassemble the two halves of the turn signal mounting clamps supplied, place the M6 X 25mm button head screws thru the hole in the side of the clamp from the inside, place the spacers supplied over the screw threads. Screw the clamps and spacers onto the turn signals. Hold the signal/clamp assemblies up to the front fork, position the signals so that the housing/lens seam is vertical and straight, carefully remove the assemblies from the forks and tighten the screws securely. Install the signal/clamps onto the forks, set to the desired height and angle and tighten the clamp screws securely. 3. Using a sharp knife slit the black wire loom from the turn signal plug back 7″. Pull the turn signal wires and plugs out from the loom. Fold the wires along the loom going down towards the headlight. Leave 2-3″ of the wire next to the plug exposed and neatly tape the rest of the wire to the loom and the loom closed back up to the handlebar switch. 4. Connect the signal wires to the plugs from the wire loom. Using the cable ties supplied tie up any loose or unconcealed wire and the plugs.

SUZUKI M109 TURN SIGNAL RELOCATION BAR

0

Filed Under (Suzuki) by admin on 21-12-2010

download
1. Remove the windscreen/headlamp assembly by removing the two (2) 4mm allen screws located on the sides of the windscreen and the two plastic rivets at the top rear (push the center pin inward º” and then pull the rivet out). Pull the windscreen/headlamp forward to gain access to the rear, unplug the headlamp and set aside. 2. Locate the turn signal wire connections and unplug them from the wire harness. On the black connectors lift the tab up to unlock the connector and on the white ones use a small screwdriver inserted into one of the two longer slots and lift the center portion up while pulling the connector apart. Remove the screws which attach the turn signals to the chrome signal mounts located on the bottom of the mounts. Pull the turn signals out from the mounts and set aside. Looking thru the hole in the mount that the turn signals were in you will see a 4mm allen screw on each side, remove these. Remove remaining two (2) 6mm allen screws located on the bottom of the steering head that attach the mounts, remove and set aside. 3. Lay out the new turn signal mounting bar (see photo). Install the signals onto the bar as shown routing the wires thru the bar and out thru the slot in the center. Install the two (2) 6 x 8mm screws supplied and tighten securely. 4. Install the bar/signal assembly onto the steering head using the two (2) 6mm allen screws removed earlier (the brake hose clip should be on the bottom below the signal mount) and tighten securely. 5. Reconnect the turn signal wires (the pale blue/green wire goes to the right signal). Turn the ignition on and test the functions of the signals and running lights. Re-install the windscreen/headlamp assembly being sure to first plug in the headlamp