HARLEY-DAVIDSON SPORTSTER MODEL'S 215 and S 215 INSTALLATION and CLEANING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1. Refer to Figures 1 & 2. 2. Remove taillight and remove seat. SAFETY: DISCONNECT BATTERY PRIOR TO ALL WIRING MODIFICATIONS 3. Disconnect Right turn signal connector inside taillight. Pull wire from the underside of fender. Cut the wire approximately 2 inches from the connector, 02/16/09 save for reinstallation. Ensure the wires are loose from all retaining clips under fender. 4. Remove nut located behind fender holding the turn signal. 5. On the right side only, Remove the two torx bolts from fender strut, carefully pull and rotate fender strut cover to remove. Pull turn signal wire completely out. Remove bolt holding turn signal to the fender strut cover. SADDLEBAG INSTALLATION 6. Reinstall the fender strut cover using the 1 7/8″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the front hole and the 1 1/2″ Hex Spool Bolt Assembly and 1/8″ x 5/16″ Aluminum Spacer in the rear hole. Refer to view “B”. Insert the chrome caps into the existing turn signal holes. Bend tabs over to ensure a snug fit. 7. Repeat disassembly and installation on opposite side. TURN SIGNAL RELOCATION 8. Install turn signal bracket between license plate and license plate bracket with ears of bracket facing the front of the motorcycle, using 1/4 – 20 x 3/4 Hex cap screws, 1/4 flat washers, and 1/4 – 20 locknuts. 9. Mount turn signals directly to bracket using 5/16 – 18 x 3/4 hex cap screws with a Black Plastic Spacer, and 5/16 star washer. For a clean installation slide rubber grommet over the wire and secure into hole in turn signal, remove top center mounting bolt on license plate bracket and run wires through this hole. Splice the connector back on the wire, and reconnect to wire harness. Ensure all wires are secure under fender. Reinstall taillight. 10. Connect battery and test turn signals for function. Information: Bags will be easier to mount and remove if a small amount of silicone lubrication is applied to rubber mounting points. 11. Mount saddlebags over spools on fender strut and secure with clips retained inside bags. 12. Inspect each clip to verify each clip is properly seated in retaining groove. See View “A”

CFC Offroad KTM RFS (Racing Four Stroke) Clutch Cover 250-400-450-520-525 EXC-XC-SX Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
1. Wash engine sidecase to remove any dirt, grease, oil, etc. 2. Clean engine sidecase and the CFC case guard with quick drying solvent such as electrical contact cleaner or brake cleaner 3. Apply an even layer of Permatex 16B silicone adhesive* to the backside of the CFC guard. This can be a messy job and most find the best tool to spread it evenly is your finger. It is suggested that you use a rubber glove to avoid skin contact. Try to get complete coverage free of voids and about 1/16-1/8″ thick 4. Align sidecase Guard with the engine sidecase, keeping the logo horizontal (if the Guard has one). Gently press on the engine sidecase. Once you feel that it is aligned and positioned properly, press with enough evenly distributed pressure to get an equal squeeze out of Permatex all around the perimeter. Don’t worry if you end up with excess. Excess adhesive can be cleaned up with a rag and mineral spirits or brake/contact cleaner. Let dry overnight 5. A couple of strips of masking tape can be carefully applied to assure the guard doesn’t move

2007 KTM 250, 450, 505, SX-F QPX Performance Tip/ Spark Arrester Clean out Procedure

0

Filed Under (KTM) by admin on 24-01-2012

download
Step 1: Take off the end cap of exhaust by removing the five (5) screws using a T-20 torx wrench. Cut the silicone around stock end cap using a box knife, then pull cap straight off. Step 2: Step 3: To install your new QPX Performance Tip/Spark Arrester, slide QPX assembly into muffler with engraving on base right side up. Step 4: Align holes of QPX base and muffler, then reinstall the five (5) original screws with your T-20 torx wrench. Installation is now complete. Store instructions in a safe place for future reference. (See clean out instructions on reverse.) If the spark arrester screen isn’t already installed in the QPX Performance Tip, remove the four (4) M6 bolts attaching the cone to the base, remove cone, install screen between base and cone, reinstall M6 bolts and tighten. Do NOT tighten. Start, but leave loose until all screws are started, the tighten securely.

Incoming search terms:

HARLEY DAVIDSON CHROME REAR BRAKE RESERVOIR COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
INSTALLATION 1. Remove and discard the screw and washer holding the rear brake master cylinder reservoir to the motorcycle frame. 2. See the Figure 1. Obtain the chrome screw (2) and washer (3) from the kit. Place the washer onto the screw threads. 3. Position the chrome rear brake reservoir cover (1) over the reservoir, lining up the holes. Fasten with the chrome screw and washer using the T27 TORX® key (6) from the kit. Tighten securely. 4. Slowly unscrew the original reservoir cap. Note the orientation of the reservoir gasket and the gasket collar, which may come off with the cap. Discard the original reservoir cap only. Set the gasket and collar aside for re-installation. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) 5. Refer to the Owner’s Manual and follow the procedure to check the brake fluid level. Fill as needed with DOT 5 SILICONE HYDRAULIC BRAKE FLUID. Do not reuse old fluid. Only use DOT 5 hydraulic brake fluid from a sealed container. 6. Set the reservoir gasket back onto the lip of the reservoir and position the gasket collar onto the gasket. 7. Carefully position the new chrome cap (4) over the reservoir and screw it on. Tighten securely. 8. Clean the indented top surface of the new cap with a 50- 50 mixture of isopropyl alcohol and water and let it dry. 9. Peel the paper backing from the Bar and Shield emblem (5). Turn the emblem to the desired orientation and press it firmly into place on the top of the chrome cap. After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury.

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN AND SMART SIREN II BATTERY REPLACEMENT MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
SECURITY SYSTEM SMART SIREN AND SMART SIREN II BATTERY REPLACEMENT KIT SIREN BOX REMOVAL Read the following instructions and make sure you fully understand them prior to replacing the battery. If the procedure is not within your capabilities, or you do not have the correct tool, have a Harley-Davidson dealer replace the battery. Improper installation could result in damage to this product. (00419b) 1. Refer to the Owner’s Manual and follow the instructions given to disarm the security system. 2. Remove the siren box from the vehicle. Reference the siren installation procedures found in the Siren Kit Instruction Sheet or contact a Harley-Davidson dealer for specific information on locating and removing the siren box from your model. Battery replacement, Smart Siren 1. See Figure 1. Remove the battery cover (2) from the siren box as follows: a. Place the siren on a sturdy, flat surface with the potting (1) and battery cover facing up. b. Using a blunt, stiff blade such as a table knife, insert the blade between the case and cover at a 45 degree angle to the side of the case. Insert the blade until it touches the snaps on the inside face of the cover. Figure 2 shows the four barbed snaps (2). c. Twist the blade slowly so the inserted edge presses against the inside face of the cover. The cover will pop off and can be replaced later using silicone adhesive if necessary

Incoming search terms:

HONDA GL1800 Chrome Mesh Grill Accents Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
NOTE: Read instructions thoroughly before installing. Work one side at a time. 1. Place bike on center stand. 2. Thoroughly clean outside surface of the chrome air intake area where inserts will be install with rubbing alcohol pads- provided. 3. Using the silicone provided, run a bead of silicone as shown in figure 1 or on the original side fairing in the same manner. 4. Carefully place insert mesh into place. 5. Press the accent into place. 6. Using two wire ties, secure the chrome accent by wrapping the wire ties through the original radiator grill as shown in figure 2. Note: You may want to use masking tape or a soft material to protect the chrome or painted surface while placing the piece on the bike. 7. Repeat on the other side. 8. Wait at least 12 hours before removing wire ties.

HONDA GL1800 DASH DOOR ACCENTS INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Note: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Run a bean of silicone (provided) on the inside edge of one of the Dash Door Accents. 3. Place the accent over the pocket and secure with wire ties (provided). Repeat on the other side. 4. Run a bead of silicone on the underside of the door latch accent and set in place. 5. Allow time for the silicone to set (at least overnight). HONDA GL1800 DASH DOOR ACCENTS INSTALLATION MANUAL