HARLEY-DAVIDSON 1979-Later Big Twin CONVERSION INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2012

download
Turn ignition switch to the OFF position. Disconnect the ground cable from the battery. 2) Disconnect the wire at the coil which runs down to the points. Remove the point cover plate. 3) Note the position of the slots in the point plate. When the Mallory UNILITEfi plate is installed, use the position of the slots to approximate the timing. 4) Remove the wire to the points. Remove the O.E. standoffs and washers. Remove the point plate assembly. 5) Remove the O.E. cam sleeve from the advance assembly. Place a small amount of oil on the advance shaft which supported the cam sleeve. 6) Slide the Mallory shutter wheel onto the advance shaft. Make sure the shutter wheel is all the way down into the advance assembly (it will only go one way due to the roll pin in the advance assembly). 7) Install the advance and shutter wheel into the nose cone. Make sure that the pin on the bottom of the advance engages the slot on the end of the camshaft. Apply Loctite to the threads and install the advance bolt. Torque to 25 in.lb. 8) Rotate the shutter wheel by hand (counter-clockwise) and release. It should rotate about 10 degrees and “snap” back when released. 9) Install the two Mallory standoffs. Place Loctite on the threads and torque to 16 in.lb. Do not use any washers with the standoffs. 10) Start the three wires of the Mallory UNILITEfi Module through the hole in the nose cone housing. (The module goes in towards the advance assembly with the flat plate outward). Pull on the three wires to remove any slack and prevent the wires from rubbing on the shutter wheel. 11) Rotate the UNILITEfi plate assembly until the slots in the plate are in the same position as the point plate was. This should make the timing close enough to start the engine. Slide the two Mallory 8-32 sleeve nuts (supplied) through the UNILITEfi plate and onto the male threads of the Mallory standoffs. Tighten the sleeve nuts just enough to prevent the plate from moving. 14) Route the wires from the UNILITEfi Module to the ignition coil, carefully avoiding the exhaust system. Connect the red wire to the positive (+) terminal (12 volts) on the coil. Connect the green wire to the negative (ñ) terminal on the coil (where the point wire was connected). Connect the brown wire to ground. The best place for the brown wire is the negative (ñ) post on the battery, however, any part of the frame or engine which is grounded to the battery will work

HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

Incoming search terms:

HONDA GL-1500 Trailer Wire Harness with Relay INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 27-02-2011

download
Seat: (if optional accessory wire is to be used) After removing trunk pan, run a stiff piece of wire from the bottom of the left saddlebag frame behind the rear tire up until it comes out under the trunk. Then hook open end of wire harness to fish wire and tape with electrical tape. Pull the harness back down to the bottom of the saddlebag frame. Route the long part of harness wire around the back of the license plate light to the right side 6-pin vertical connector just in front of tail light assembly. Unplug the stock connector and plug wire harness in between the stock plugs. Do the same for the left side with the short side of the Y on the harness. Now pull the slack down from the bottom of the harness and tuck all of the wires under the frames tubes so that the pan can be reinstalled without any problems. You can now hook up the loose ends of the harness to any style connector to match your trailer connector using the following color codes: GREEN GROUND ORANGE- LEFT TURN YELLOW- BRAKE BLUE- RIGHT TURN BROWN- TAIL RED POWER . Note : This accessory is an electronic isolated trailer wire harness. It should be installed by a qualified mechanic . 1. Disconnect the negative from the battery. 2. Install the harness. 3. When connecting to the trailer make sure all wires are used for the proper use and are waterproof. Make sure there are not exposed wires. Consult the trailer manufacturer for proper wiring. 4. Reconnect the battery negative. Double check the functions

SUZUKI INTRUDER 1500 LC BOTH WHEELS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 27-02-2011

download
In order to keep the proper balance on the bike lift, I would suggest that the front wheel be removed first, this is comparatively easier than the rear wheel which will be explained later. Front wheel removal : Remove the end caps, remove the front axle “Pinch Bolt” front left fork ( item (2) in manual ) remove caliper bolts both (2) both sides (2003 model year) secure calipers, secure wheel from dropping while removing axle from left side. Remove front axle, caution : there are (2) spacers on this axle, left & right, make sure you mark them, as they are both different in shape & in length, & must be re-assembled in same order to provide proper cetrallity of the front wheel with the forks & the brake calipers.both spacers have large flanges which go towards the bearing, the right spacer has (2) flanges, the largest dia. goes towards the bearing. ( very important) Now comes the tough part, I had the original stock pipes, so if you have different pipes, or your bike is a different year, (2003) your choices may be different from mine. Remove OEM right side saddlebag, slack off muffler coupling brackets # 8 & # 8a which connect muffler crossover tank to top muffler, this is where the power of the allen socket wrench set will come in handy, they’re pretty tight with the heat,remove top exhaust pipe bracket bolt (item 19 in manual) the top exhaust pipe should now swing down clear of the rear axle. You may be forced to provide more room for the exit and/or re-installation of the rear wheel by removing the bolt which secures the underside mufflet tank on the lower left side of the frame, (item # 13 in manual) then the (2) bolts, ( items # 14 in manual) which will allow the rear muffler body ( lower exhaust pipe ) to be pulled over to the right to provide access for easier rear wheel entry or removal

Incoming search terms: