HARLEY DAVIDSON PASSENGER FOOTBOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards: Existing Footboard Insert Removal NOTE Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces. 1. See Figure 1. Fold the passenger footboard (1) into the UP position. 2. Loosen, but do not remove the footboard insert setscrew (2). 3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan. 4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan. 5. If replacing both inserts, repeat for the opposite footboard. Swept Wing Passenger Footboard Installation 1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards: •Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit. •Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket. 2. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards. Footboard Insert Installation 3. ALL applications: Center the two footboard pivot pins. 4. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert. 5. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place. 6. Fold the passenger floorboard UP and tighten the setscrew to secure the insert. 7. Repeat Steps 3 through 6 for the opposite footboard. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON LOWER FORK BRACKET (TRIPLE TREE) COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. For models equipped with air baffle: See Figure 1. Remove and discard the two hex screws (2) and flat washers (3) holding the baffle (1) to the fork stem and bracket assembly(4). Retain the baffle for later reassembly. For models not equipped with air baffle: Remove and discard the two plugs from the rear of the fork stem and bracket assembly (4). 2. Remove and discard the hex socket head screw (6) holding the brake line manifold (5) to the underside of the fork stem and bracket assembly. 3. Place the lower fork bracket cover into position covering the brake line manifold. Attach the cover (and the baffle, if so equipped) to the fork stem and bracket assembly with the two 1/4″ self-tapping hex screws from the kit. Tighten securely. 4. Install the 5/16″ self-tapping hex socket screw through the cover and brake line manifold into the stem and bracket assembly. Torque to 10-15 ft-lbs (13.6-20.3 Nm). 5. Verify that the throttle and clutch cables are routed properly and do not interfere with steering the vehicle. After disturbing the brake system, BEFORE moving motorcycle, you must pump brake fluid until the pistons push the pads against the brake disc. If you don’t pump fluid pressure up again, the brake will not be available to stop the motorcycle which could result in death or serious injury. After disturbing the brake system, always test motorcycle brakes at low speed. If brakes are not operating properly, or braking efficiency is poor, testing at high speeds could result in death or serious injury

HARLEY DAVIDSON CHROME PASSENGER FOOTBOARD SUPPORT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
Removing Passenger Footpegs 1. Remove and discard the socket screw and lock washer attaching the existing footpeg bracket to the rear swing arm bracket. Proceed to Step 5. Removing Passenger Footboard Supports 1. For standard footboard 50613-91: See the Service Parts illustration. Tilt the footboard to the “up” position. Remove the underside chrome footboard covers if so equipped. From the bottom of the footboard, use a small flat-blade screwdriver to push the rubber beads on the pad up through the holes in the footboard pan. Remove the pad. For swept-wing (FLHRS- and FLHTCSE-style) footboards: With the passenger footboard in the “down” position, carefully raise an outside “corner” of the stock footboard insert off the footboard pan with a suitable flat-bladed tool, taking care to avoid scratching the chrome footboard pan. Continue around the edge of the footboard, using a second flat-bladed tool if necessary to pry up and remove the old insert. 2. Using a brass drift and rubber mallet, tap one pivot pin (6) out of the pivot hole into the center pocket of the footboard pan, remove the pin and set it aside. Repeat for the second pin. 3. Remove the footboard from the support bracket (1). Remove and discard the steel ball (5) and spring (4) from the hole in the bracket. 4. Remove and discard the socket head screw (2) and lock washer (3) attaching the footboard support bracket to the rear swing arm bracket. Proceed to Step 5. Installing the New Footboard Supports NOTE Three holes are available in the rear fork brackets for footboard support mounting. Depending on model and year, the footboards can be installed in any of two or three positions for passenger comfort. A plastic plug, inserted in the upper hole at the factory, can be removed. 5. See the Service Parts illustration. Position a new chrome footboard support (1) against the swing arm bracket at the desired height. The left and right supports are identical. With the locating peg on the footboard support in the next lower hole, fasten the support with a hex socket screw (2) and lockwasher (3) from the kit. Tighten the screw to 15-18 ft-lbs (20-24 Nm). 6. Place the new spring (4) into the retaining hole in the footboard support. Rest the detent ball (5) on top of the spring