HARLEY DAVIDSON XL 2-UP CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Additional Parts Required •XL883 and XL883L models require the separate purchase of Passenger Footpeg Kit 50203-04, which is available from a Harley-Davidson dealer. •XL1200N, XL883N and XL1200X models require separate purchase of guide washer 7487. Kit Contents See Table 1 and Table 2 for the kit number and corresponding grabstrap number. See Figure 7 and Table 3 for a list of the service parts. Table 1. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52883-04A 51295-04 51686-05 51312-07 52907-04A 51295-04 52283-06 51312-07 52923-04B 51295-04 52299-06 51312-07 52859-04B Table 2. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52849-04B 51295-04 51386-04 51312-07 52871-04A 51295-04 51684-05 51312-07 52884-04A 51295-04 51685-05 51312-07 52916-04B 51295-04 52176-06 51295-04 52184-06 INSTALLATION NOTE When installing this kit, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. Models Originally Equipped With Solo Seat 1. Remove the seat according to the instructions in the owner’s manual. 2. See Figure 1. Remove and discard seat post washer (2) and screw (3) from the front fender hole. 3. For XL883 and XL883L models: See Figure 2. Remove plastic cap (1) from rearward fender hole and save. 4. Remove retention nut (2) and washer (3) from middle fender hole

HARLEY DAVIDSON DYNA PASSENGER PILLION SEAT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVE SEAT NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove screw to detach rear seat mounting bracket from fender. 2. Remove two capscrews that attach seat mounting bracket to bottom of stock seat. 3. Remove the existing seat from the motorcycle. Save the seat bracket and mounting screws for installation of the new seat. 4. If motorcycle has a grabstrap installed, remove nut and washer that holds passenger strap in place and remove strap. 5. See Figure 1. Remove the plastic cap from rearmost fender hole (3). 6. Remove the seat retention nut and washer from the solo seat mounting hole. 7. See Figure 2. A cable strap may be used as an installation aid to remove and reinstall the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the rearmost fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. 8. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap. 2 5 1 2 1 3 6 7 4 is00363 1. Retention nut and washer (2-up seat positon) 2. Retention nut and washer (solo seat position) 3. Rear-most fender hole 4. Middle fender hole 5. Grabstrap mounting hole 6. Flange screw 7. Plastic retention nut

HARLEY DAVIDSON FXD SOLO SADDLE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Removal of Stock Seat 1. Remove screw (6) to detach rear seat mounting bracket (9) from fender. 1996 models will have a nylon washer under the bracket that should also be saved for installation of new seat. 2. Slide seat rearward to unhook front of seat from frame, then pull seat forward out of passenger strap. 3. Remove two capscrews (10) that attach seat mounting bracket to bottom of stock seat. Install original seat mounting bracket to bottom of new solo saddle with original capscrews. Tighten capscrews securely. 4. Remove nut (7) and washer (8) that hold passenger strap (11) in place and remove strap. Installation of Kit Seat This seat is for solo driver use only. Do not attempt to carry a passenger with this solo seat installed. Use of a luggage rack, fender, or tail section as an additional seat may result in death or serious injury. NOTE When a solo seat is installed without a passenger seat, the passenger footpegs or footboards and the passenger grabstrap must be removed. For 1996 models: 1. Slide seat into position until front seat tab engages frame, then place original nylon washer under hole in rear seat mounting bracket and secure bracket to fender with screw (6). NOTE For 1997 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 models: 1. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 2. Place retention nut (3) over cable strap (2) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 3. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 4. Slide seat into position until front seat tab engages frame, then secure rear seat bracket to fender with screw (6). Install chrome cap (5) in rear retention nut

HARLEY DAVIDSON SIGNATURE SERIES SOLO SEAT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL NOTE Refer to owner’s manual or service manual for seat removal instructions for your model. 1. Remove right and left saddlebags according to the instructions in the service manual. Save saddlebag mounting brackets and hardware. 2. Remove passenger seat strap. Discard passenger seat strap. 3. Remove existing seat from vehicle. 4. See Figure 1. Remove and discard stock nuts (2) from studs (1) on rear fender (3). INSTALLATION Install Rider Seat 1. Push front seat on frame with mounting bracket at rear. 2. Firmly push front of seat downward and rearward until frame tongue engages slot in seat. 3. Push seat forward until studs are centered in slots of mounting bracket. 4. See Figure 4. Install two nuts (4) on studs to secure rear seat mounting bracket to rear fender. Alternately tighten nuts to 60-96 in-lbs (6.8-10.9 Nm). 5. If installing a new passenger seat, refer to the instructions included with the kit. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. If installing passenger seat, install passenger seat strap following the instructions in the service manual. 7. Install right and left side saddlebags following the instructions in the service manual. 1 2 3 2 1 is04121 1. Stud (2) 2. Nut (2) 3. Rear fender Figure 1. Rear Fender Install Rider Backrest NOTE Flaps shown removed for clarity of illustration. 1. See Figure 2. Turn backrest assembly (1) at a 45 degree angle clockwise to the seat. Slide the backrest shaft (2) through the flaps and into the receptacle in the seat. 2. While pushing down on the backrest assembly, twist the backrest counterclockwise until the shaft hits the stop. 3. Verify that the backrest assembly is locked in place by pulling up in the backrest pad

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON DYNA SEAT WITH ADJUSTABLE RIDER BACKREST INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION Seat Installation NOTE When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. 1. Remove the existing seat and passenger grab strap following the instructions in the appropriate Service Manual. Discard the grab strap and retain all other hardware for later use. 2. See Figure 9. Remove the seat bracket from the stock seat. 3. For all except FXDWG: Install the stock seat bracket onto the new seat with the stock screws. For FXDWG: Install new seat bracket 52152-97 onto the new seat with the stock screws. For models equipped with original or accessory two- up seating: Proceed to Step 6. 4. On models equipped with an accessory Solo Seat: Remove the plastic plug from the hole in the rear fender where the rear seat bracket will be attached. 5. See Figure 9. Slide the retention nut (9) onto the cable strap (11) so the wide end of the nut rests on the eye of the strap. Thread the cable strap up under the fender and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. Seat the rib of the retention nut in the notch in the fender hole and slide the retention washer (10) into place from the rear. This will lock the retention nut in place. 6. See Figure 1. Place the black bracket (1) from the kit onto the frame as shown. 7. See Figure 9. Install the new grab strap (8) in the original location with the hardware saved in Step 1. Tighten the nut to 96 in-lbs (10.85 Nm) . 8. See Figure 1. Install the screw (2) in the hole on the forward edge of the bracket. Attach the locknut (3) and washer (4) from under the frame. Tighten to 96 in-lbs (10.85 Nm)

HARLEY DAVIDSON DYNA ACCESSORY SEAT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
For vehicles with 2-up seating 1. Remove the existing seat from motorcycle. Save the mounting screw for installation of the new seat. 2. Remove existing grab strap and all attaching hardware. 3. See Figure 1 for information on which holes to install grab strap through for your seat (use the hole shown dark in the illustration). Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). Tighten to 60-90 in-lbs (6.78-10.17 Nm) . 4. Position new seat on motorcycle. Be sure tongue on front of seat fully engages into the seat mounting slot between the gas tank bracket and frame. 5. Secure seat with stock screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Kit Number: 52284-06 and 52359-06 Kit Number: 52159-06 Kit Number: 51540-06 Kit Number: 52288-06 Kit Number: 51471-06 and 51472-06 Grab StrapNumber: 52370-04 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Kit Number52378-07 Grab StrapNumber: 52313-96 is03552a Figure 1. Grab Strap installment information For vehicles with solo seat 1. Remove the existing seat from the motorcycle. Save the mounting screw for installation of the new seat. 2. See Figure 2. Remove the plastic cap from the rear most fender hole (3). 3. Remove the seat retention nut and washer from the solo seat mounting hole