HARLEY DAVIDSON DYNA CHROME COIL COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Installation 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Note the position of each spark plug wire in the ignition coil, then disconnect the two wires. 3. If there is an existing coil cover: Remove and discard the coil-cover mounting screws and spacers. Remove and discard the coil cover. If there is not an existing coil cover: Remove and discard the two coil mounting screws. 4. See the Service Parts illustration. Obtain the coil cover bracket (3), two long screws (4) and two spacers (2) from the kit. 5. Insert the screw into one of the holes in the bracket as shown, through a spacer, and into a coil mounting hole. Repeat with the second screw and spacer. 6. Assemble the coil to the electrical caddy with the two screws. Tighten the screws to 50 in-lbs (5.6 Nm). 7. Obtain the new chrome coil cover (1) from the kit. Position the cover over the coil, and fasten to the coil cover bracket with the three chrome screws (6) and washers (7) from the kit. Do not fully tighten the screws at this time. 8. Connect the spark plug wires through the holes in the side of the coil cover onto the correct coil terminals. 9. Adjust the cover to center the spark-plug wire boots in the coil cover holes for best appearance. Tighten the three chrome screws securely 10. Refer to the Service Manual and follow the instructions given to install the maxi-fuse

Incoming search terms:

HARLEY DAVIDSON HERITAGE SOFTAIL WIND DEFLECTORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
This kit is designed for 1986 and later FLSTC, FLST, FLSTF and FLSTN model motorcycles equipped with a windshield and/or passing lamps. If your FLST, FLSTC, FLSTF or FLSTN is equipped with a windshield but not a passing lamp assembly, you will need two washers 5/16 x 1 x 1/8 in. (HD Part Number 6645). These washers will be used as spacers for the bottom of the deflector. This kit is also designed to fit with accessory five gallon Fat Bob Gas Tanks. Installation 1. See Figures 1 and 2. On Rigid Mount Windshields, remove the bolts (1), lockwashers (2), and flat washers (3) securing one side of the windshield support bracket. Save all hardware for reinstallation. NOTE On Rigid Mount Windshields, be sure the large spacer (4) between the tip of the windshield support bracket and the fork stays in position. On Detachable Windshields, remove the bolts (1) and flat washers (2) securing one side of the windshield support bracket. Save all hardware for reinstallation. 2. Place the wind deflector in position and install the hardware removed in Step 1. Do not tighten the bolt at this time. NOTE On Rigid Mount Windshields, be sure you install the large spacer between the windshield support bracket and the fork. NOTE On 2000 and later models, be sure the wind deflector is outside of the windshield docking points. 3. Position the wind deflector parallel with the fork leg and install the other flat washers, lockwashers and bolts. Do not tighten the bolts at this time. NOTE If you have a motorcycle equipped with a windshield, but no passing lamps assembly, use the washer (6645) to space the deflector away from the fork leg. 4. Position the wind deflector so it does not touch the bottom of the windshield or the turn signal. The deflector bolt holes are slotted for th is purpose. 5. When the deflector is correctly positioned, tighten the bolts to 17 ft-lbs (23 Nm). 6. Repeat steps 1-5 for the opposite side of the vehicle

Incoming search terms:

HARLEY DAVIDSON DYNA CHROME SWINGARM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
This kit fits all 2006 and later Dyna model motorcycles. INSTALLATION NOTE Refer to the appropriate Service Manual for detailed information on the following generalized steps. 1. Remove the rear fork. 2. Remove the bearing, spacer and retaining ring from left side pivot bore of the stock swingarm. 3. Install the bearing, spacer and retaining ring removed in the previous step, into the left side pivot bore of the chrome swingarm. 4. Install the dust shield and bushing, from the kit, into right side pivot bore of the chrome swingarm. 5. Install the chrome swingarm kit. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON TOURING DETACHABLE SOLO TOUR-PAK RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Installation NOTE See Service Parts Ilustration. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak to desired location. 1. Place Tour-Pak on support tube and open lid. NOTE In the following Step, the longer bolts (Item 7), are used for King and Chopped Tour-Paks while the shorter bolts (Item 6) are used for Leather Tour-Pak. 2. See Service Parts Illustration. Obtain bolt (6 or 7), two flat washers (4), concave spacer (5) and hex lock nut (3) from kit. Align rear center hole in Tour-Pak with same hole in support tube (9). Slide bolt with flat washer through Tour- Pak, through support tube, then through concave spacer (with concave side facing surpport tube). At bottom of support tube, install washer and nylock cap nut (3). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. See Service Parts Illustration. Obtain bolt (6 or 7), flat washers (4), concave spacer (5) and hex Nylock nut (3) from kit. Align the remaining four holes in Tour-Pak over holes in solo rack. Slide bolt with flat washer through Tour- Pak, through support tube (9), then through concave spacer (5) (with concave side facing up) and Solo Rack hole. At bottom of Solo rack, install washer and nylock cap nut (3). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. Always install the mounting bolts from inside the Tour- Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack

Kawasaki Vulcan Front Suspension Lowering Kit Installation manual

0

Filed Under (Kawasaki) by admin on 27-02-2011

download
INSTALLATION 1. This lowering method requires replacement of the front spring spacers. This is a simple task, and is completely reversible. First, raise the front tire off of the ground before you begin. Raise the motorcycle so no weight is applied to the front wheel. 2. Cover the gas tank with a thick towel to prevent scratching. Don’t omit this…you’ll be sorry if you do! 3. If the handlebar risers are OEM (stock), loosen the handlebars in their clamps and lift them from the risers, carefully placing them on the gas tank on a thick towel to prevent scratching. This will allow room for the spring spacers to be removed from the front forks. 4. Using a small knife blade, sharp screw driver, etc. in the pinch grove on each side of the triple clamp, gently pry upwards and pop the chromed plastic covers off. These are the covers on the top of the front forks, covering the spring retainers. Below these chrome caps, you’ll find a gold anodized metal plug with a small counter bore in the center. This is the part used to retain the springs within the front fork tubes. Using an extension bar, large Phillips screwdriver, etc., press down a bit in the counter bored area of the plug to take the pressure off of the small internal “C” ring. While this “gold” colored plug is depressed, remove the internal C-ring. The C-ring is made of small diameter wire. Once the C-ring is removed, slowly release the pressure on the plug and it’ll push itself out of the top of the shock. The picture below is of the upper fork leg with the gold retaining plug removed. 5. Stick a finger into the fork tube, and slide the OEM tubular spacer up and out of the fork tube. 6. The picture below illustrates the use of a Scootworks lowering spacer with the fork spring. On the right hand end of the you’ll see a Scootworks lowering spacer. The fork spring stays in the front fork, and you’ll drop in the spacer with the desired amount of lowering. The approximate amount of lowering is marked on each Scootworks spacer. 7. Select the spacers for the desired amount of lowering. The longest spacers supplied are marked as [1] and will lower the front suspension 1″. The spacers of middle length are marked as [2] and will lower the front suspension by 2″. The shortest spacers supplied in the kit are marked as [3] and will lower the front suspension by 3″. Omission of the spacers completely will lower the front suspension by approximately 4″. 8. Install the selected spacers in the fork tubes, on top of the internal fork spring. Place the gold anodized metal plugs on top of the spacers and press them back into the fork tube. Be sure to turn the metal plug so the side with the counter bore is facing outwards. Reinstall the C-rings, and gently lower the front end back to the ground. Make sure the C-rings seat themselves in their respective grooves when the weight of the bike is placed back on the front end. Re-install the chrome caps.

Incoming search terms:

SUZUKI INTRUDER 1500 LC BOTH WHEELS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 27-02-2011

download
In order to keep the proper balance on the bike lift, I would suggest that the front wheel be removed first, this is comparatively easier than the rear wheel which will be explained later. Front wheel removal : Remove the end caps, remove the front axle “Pinch Bolt” front left fork ( item (2) in manual ) remove caliper bolts both (2) both sides (2003 model year) secure calipers, secure wheel from dropping while removing axle from left side. Remove front axle, caution : there are (2) spacers on this axle, left & right, make sure you mark them, as they are both different in shape & in length, & must be re-assembled in same order to provide proper cetrallity of the front wheel with the forks & the brake calipers.both spacers have large flanges which go towards the bearing, the right spacer has (2) flanges, the largest dia. goes towards the bearing. ( very important) Now comes the tough part, I had the original stock pipes, so if you have different pipes, or your bike is a different year, (2003) your choices may be different from mine. Remove OEM right side saddlebag, slack off muffler coupling brackets # 8 & # 8a which connect muffler crossover tank to top muffler, this is where the power of the allen socket wrench set will come in handy, they’re pretty tight with the heat,remove top exhaust pipe bracket bolt (item 19 in manual) the top exhaust pipe should now swing down clear of the rear axle. You may be forced to provide more room for the exit and/or re-installation of the rear wheel by removing the bolt which secures the underside mufflet tank on the lower left side of the frame, (item # 13 in manual) then the (2) bolts, ( items # 14 in manual) which will allow the rear muffler body ( lower exhaust pipe ) to be pulled over to the right to provide access for easier rear wheel entry or removal

Incoming search terms:

Harley-Davidson Six Speed Transmissions Reverse Gear Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the exhaust pipe support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.8 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.9 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Installation 3.1 Reinstall exhaust pipe support bracket with the supplied two 5/16-18 x 1 3/4″ long hex head bolts and the ¼” thick spacer between engine and bracket. Figure 1 3.2 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.3 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 2 3.4 Install the supplied plug into the main shaft hole. To be removed later. 3.5 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 3 3.6 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.7 Remove torque wrench from special tool. Do not remove special tool from small gear

HARLEY DAVIDSON FOUR-POINT DETACHABLE DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 3. Remove the screw (A) retaining the rear of the chrome cover to the rear frame extension on each side of the vehicle. 2. Place a washer (7) over the threads of each of the larger TORX® head screws (6) from the kit. Apply 2 or 3 drops of Loctite 262 Threadlocker and Sealant – Red to the threads of each screw. Install the screws through the docking plates (1) and fender covers, and into the threaded holes in the frame extensions on each side of the vehicle, and tighten to 17 ft-lbs (23 Nm) . NOTE See Figure 1. The docking points must be attached to the docking plates (2) with the chamfer (1) facing the plate and the flat side facing out. 1 2 is05506a 1. Docking point chamfer (bevel) 2. Mounting plate Figure 1. Docking Point Installation 3. See Figure 3. Slide a spacer (2) onto the longer pin (B) of each docking plate. Install the four docking points (3), chamfer end first, onto the long and short docking plate pins using the washers (5) and smaller TORX screws (4). Tighten to 10.5 ft-lbs (14.2 Nm) . NOTE Protective tape must be installed to the rear saddlebag mounting bracket to prevent damage to the saddlebag finish when the lid is opened. 4. See Figure 2. Apply protective tape (2) to the rear mounting bracket (1) on the saddlebag in the location shown. Repeat for the other side. 2 1 is05533 1. Rear saddlebag bracket (2) 2. Protective tape %lengthT=0

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

HARLEY DAVIDSON XL SPRING SEAT MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION 1. Refer to service manual and remove the existing seat, seat post, washer and screw. Do not remove grommet or T-spacer from rear fender. Save the washer and screw for later installation. 2. See Figure 1. Clean the frame surface where the hook- and-loop strip will be attached with a 1:1 mixture of isopropyl alcohol and water. Let it dry completely. 3. Install the frame cover to the frame as follows: a. Remove the loop side of the hook-and-loop (3) from the bottom of the frame cover (1). b. Remove the protective tape from the hook-and-loop strip and attach it to the frame as shown. Wrap it under the frame or trim excess length, if necessary. c. Orient the frame cover so that it covers the seat pan and secure the cover to the frame with the hook-and- loop strips. 4. See Figure 3. Install two springs (2) to the mounting bracket (1), oriented as shown, with screws (3). Tighten screws to 25-30 ft-lbs (34-41 Nm) . 5. See Figure 3. Install mounting bracket to frame tab a. Install mounting bracket (1) over frame tab. Orient it so that the two retaining tabs on the mounting bracket will hold down and be fully seated on the frame cover. b. Secure mounting bracket with screw (B), washer (C) and nut (4). Do not tighten. c. Center the frame cover and mounting bracket to the motorcycle frame. d. Tighten mounting bracket screw and nut to 15-20 ft- lbs (20-27 Nm) . 6. Install seat pivot bracket (15), washers (14) and screws (13) to the seat. Tighten screws to 48-72 in-lbs (5.5-8.0 Nm) . 7. Remove the rear fuel tank mounting screw, washers, nut and thread protector. Save washers for later installation

Incoming search terms: