Honda GL1000 Timing Belts Removal / Installation Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Turn engine as described above until the T-1 mark aligns with engine block marks (it looks a little ‘out’ on the photo, it’s the angle). AND (this is important) the pulley marks align with the marks on the engine cover like here on LEFT side (seen from sitting on bike … remember). and RIGHT side. Mark this position on the central pulley and engine block. Now release the tensioner bolts. (*) And remove the belt. (*) (*) When you do that the right pulley (photo-left) will ‘wander/turn’ out of position when you remove the belt, as it is ‘riding’ on cam ‘slope’ (which is under the influence of the valve springs). Don’t worry. One thing you can do to calm your nerves and keep it in position: put the new belt loosely over the pulley and holding the pulley in the CORRECT POSITION (marks aligned) ‘strip’ a spanner to the frame. Do not use the spanner to turn the pulley. Use your hands … then ‘lock’ it with the spanner. (Make absolutely sure you do not turn (release/loosen) the bolt). And, here’s a nifty trick posted by Mooseheadm5 in another thread: “..one thing that made it super easy (and 3 reduced the anxiety level quite a bit) was that I loosened the tappet adjusters all the way [...snip...] you do not have to fight the valve springs much, plus the cams do not want to snap back or forward so you do not necessarily need to use Octane’s zip-tied wrench trick.” – Thanks, Moosehead . Release left tensioner bolts . Remove belt. Put on new belt. Check the tensioners or ‘tension rollers’. You may think they are ‘fine’: they ‘roll’ and don’t make funny sounds? You won’t know until you’ve had a set of new rollers in your hands. They should be real ‘tight’ as a set of new roller bearings … which I think they are, in fact. If they appear ‘dry’ or make any sounds; renew them and get rid of that high pitched whining sound associated with ‘dry’ rollers. This is how they go on left side (remember…photo-right). And the spring gets attached . … Pulleys in correct position (crank pulley and cam pulley) . … Left belt tight at the bottom … Tension roller loosely attached (let the spring do the tension). (On photo it is not on yet … ooops.

Incoming search terms:

2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

Kawasaki Ninja 650R / ER-6F for Cowling Panel Vibration Damper Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the three plastic clips which secure the two halves of the belly pan. First pull the centre pin to it’s out position using a flat blade screwdriver, use a spanner or another screwdriver shaft wrapped in a rag to act as a pivot point. Care should be taken not to damage the surrounding paint. With the centre pin pulled out, the clip can be removed by hand. Remove the two hex screws and clear plastic washers on each side that secure belly pan to the left and right main cowling panels. Note these hex screws are longer than all other hex screws used, take care not to mix. Remove the lower rear hex screw, stepped washer and clear plastic washer on each side and remove the belly pan. The left and right main cowling panels have tangs which locate into their respective belly pan halves

Incoming search terms: