2004 or later Harley Davidson Speedometer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Speed Sensor Installation: The microSpeed™ speedometer can be used with either +12V or +5V hall effect electronic sensors located in transmission. Sensor is not include. If your sensor operates on +5V DC wire speedometer to sensor and power as shown in Figure 2 below. Please note that color of wires from the sensor may vary, check sensor documentation for proper signal connections. For +12V sensor you will not need the Blue wire of the microSpeed™ speedometer. It may be cut short, but make sure that the end is properly protected so that it will not accidentally short to metal on the motorcycle. Use Figure 3 below for wiring a +12V sensor. H-D motorcycles 1999 and earlier used +12V sensors. H-D motorcycles 2000 and later use +5V sensors. Note: H-D OEM sensors require 20Kohm resistor(provided) between Sensor power and Sensor signal as shown. Procedure: 1. Locate wires and determine connection points. Cut wires and techflex to proper lengths. 2. Connect speedometer wires to proper signal wires as shown in diagrams, including 20K ohm resistor if using stock H-D sensor. Use either butt connectors provided or customer supplied connectors. 3. Use electrical tape or Heat Shrink tubing around sensor signal wire, sensor power, and resistor to protect resistor. 4. Proceed to Setup Section below. Setup microSpeed™ Speedometer: 1. Before proceeding review User Guide document for detailed instructions on following procedure. 2. Turn on power to speedometer, display should read “odo” 3. Set initial odometer value 4. Turn off power for 2 seconds; then turn power on again 5. Display should read “F 0″ 6. Enter Configuration and Calibration and set speedometer to proper operating mode. a. Harley English b. Harley Metric c. Standard speed sensor English d. Standard speed sensor Metric 7. Set Fuel miles per tank 8. Set Oil change interval 9. Set Speed adjustment 10. Confirm. 11. Test speed is reporting properly and adjust is necessary

Incoming search terms:

Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

HONDA CBR 1000 RR ALFANO systems Installation

0

Filed Under (Honda) by admin on 26-11-2011

download
If the sensor doesn’t start to the passage on the magnetic field, use one or several spacers to bring the sensor closer to the ground. – When fixing the cable with nylon tighten-cables, take care to move this one most possible away of the exhaust Fix the magnetic support (supplied) on one of the arms of the disc brake support with a nylon tighten-cable (see photos). Fix it on the narrowest part of the arm. – With a scorer, draw a feature on the mudguard in front of the magnetic support n this case, install the speed sensor to « 90° ». – Put down the mudguard and fix the speed sensor and its cable with nylon tighten-cables. For that to make, pierce holes of diameter 3mm (to see photos)

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
REMOVE UNION a. Remove the 2 unions. b. Remove the 2 O-rings from the 2 union. 3. REMOVE TRANSAXLE CASE PLUG NO. 1 a. Remove the transaxle case plug No. 1 from the transaxle case. b. Remove the O-ring from the transaxle case plug No. 1. 4. REMOVE SPEED SENSOR a. Remove the 2 bolts and 2 speed sensors from the transaxle. b. Remove the 2 O-rings from the sensors

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

2005 Yamaha Royal Star Tour Deluxe speedo Healer Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
The speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart.Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

Harley Davidson Dakota Digital HLY-6000 Road Star Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
The Road Star wiring is split into 2 different bundles with black connectors on the ends that were used to plug into the stock gauge cluster. Cut off both connectors. They are no longer needed The speed sensor wires on the HLY-6000 have a connector on the end that allows you to plug it directly into Harley Davidson speed sensors by using an appropriate adapter (sold separately). Luckily for us, the Road Star’s stock speed sensor will work just fine without an adapter so go ahead and cut off that connector, you don’t need it.
Ideally, the best location for the “brain box” unit of the HLY-6000 would be under the left side cover. Unfortunately, mine is full of other stuff so I had to improvise the location and decided to mount it to the back portion of the under-seat area. I would recommend that you mount yours under the left side cover though. The wires are the perfect length for that location. The brain box and wires could fit under the right side cover, but I don’t believe that the main gauge connector would reach. Using the wiring scheme on the last page of this guide, match up the wires on the Road Star with the corresponding wires on the HLY-6000 wiring harness and solder them together. Important Wiring Information: Both BLACK wires on the brain box need to be connected directly to the (-) terminal on the battery. Don’t connect them to anything else. The following wires from the Road Star are not used and can be taped off: • BLACK • RED / GREEN • BROWN The following wires from the HLY-6000 are not used and can be taped off: • GRAY • WHITE/ BLUE • WHITE (on main harness) • BROWN (*optional) The HLY-6000 has a “dimmer” function which is controlled by the BROWN wire. If you want the gauge to be bright all the time, then leave this wire disconnected. If you want the gauge to dim for night driving, then connect this wire to the GREEN Low Beam (+12v) wire

Incoming search terms:

PGR-1000-F Programmable Gear Readout Fairing Mount Installation Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
The PGR-1000 is designed for motorcycles with an Electronic VSS signal. Most modern motorcycles use a 3-wire hall-effect type speed sensor in the transmission with a power, ground, and a signal wire. The SEN-1019 is available for motorcycles without a factory VSS signal, fabrication will be required for sensor mounting. 1996-2003 Harley Davidson wiring All signal wires should be found behind the speedometer or tachometer along with power and ground. Neutral should be at the indicator lights. Signal Wire Color Speed White/Green Tach Pink Neutral Tan Power Orange Ground Black MAN#650194 2004-2007 Harley Davidson wiring The power, ground, and neutral can be found behind the speedometer and indicator lights. Speed signal and Tach need to be run to the ECU or cruise control module where you should find the wire colors listed here. This is due to the data bus configuration. Signal Wire Color Speed White/Green (Pin 33 @ ECU) Tach Pink (Pin 3 @ ECU) Neutral Tan Power Orange Ground Black 2008-2009 Harley Davidson wiring The power, ground, and neutral can be found behind the speedometer and indicator lights. Speed signal and Tach need to be run to the ECU or cruise control module where you should find the wire colors listed here. This is due to the data bus configuration. Signal Wire Color Speed White/Green (Pin 40 @ ECU) Tach Blue/Orange (Pin 54 @ ECU) Neutral Tan Power Orange Ground Black

2004+ Victory motorcycles PGR-1000 SERIES Programmable Gear Readout Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
1. Turn the key on and make sure the transmission is in neutral and ‘n’ is displayed on the readout. (Please leave the key ‘ON’ for about 5 seconds before continuing) 2. Turn the key off (.1 seconds) and then back on (1 second) again rapidly. The display should show 1 bar. If you wait too long before continuing the readout will exit the setup routine. (If the unit has already been cleared, it will immediately jump to step 6.) 3. Repeat step #2. The display should show 2 bars. 4. Repeat step #2. The display should show 3 bars. 5. Repeat step #2. The display should show 2 bars. 6. Repeat step #2. The display should show ‘n’ with a bar over it. If the display is upside down then kick the transmission out of neutral and the display will invert and show ‘C’. Tach adapter(for open-collector tach signal from ECM w/out pull-up resistor) ( 2004+ Victory motorcycles use this option , most other bikes use application on front page) VSS Notes: The PGR-1000 is designed for motorcycles with an Electronic VSS signal. Most modern motorcycles use a 3-wire hall-effect type speed sensor in the transmission with a power, ground, and a signal wire. The SEN-1019 is available for motorcycles without a factory VSS signal, fabrication will be required for sensor mounting

Incoming search terms:

Incoming search terms: