Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

2005 Yamaha Royal Star Tour Deluxe speedo Healer Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
The speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart.Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

Triumph Daytona 600 Installation of a Speedo Healer

0

Filed Under (Triumph) by admin on 28-10-2010

download
This is a step by step instruction on the new 4.0 version of the Speedo Healer on a Triumph Daytona 600. This is a “plug and play” connection that will take between 30 minutes to an hour depending on how well you know your Triumph Daytona. The tools you will need are a 5mm Allen wrench and a pair of pliers and a 10mm socket wrench. Let’s get started. First you will have to make sure you have everything. You should have the Speedo Healer, main wiring harness, speed recall wiring harness, and zip ties. 1/10 Next if you have a rear stand this will be the time to put your bike on its stand. If you don’t have one that is fine, but it makes life a lot easier if you do. Next you will have to remove your seat. You will need your Allen wrench and to get to the screws you have to pull back on the seat and you will see two screws, remove both of them. Then you should be able to lift and pull the seat off. Set the seat aside. 2/10
Next you will see two gold colored round spools. Use your Allen wrench to remove both of these, there is one on each side. Next you will see two tabs that are turned over the gas tank. You will need to turn these so they are not touching the gas tank. Some times you can do this by hand, but you might need to loosen it with a 10mm socket. 3/10 Next move up to the top of the gas tank next to the yoke and there will be another screw that you need to remove with your Allen wrench

2006 Triumph Daytona 675/ Kit: SH-V4 + SH-T02 Speedo Healer Installation

0

Filed Under (Triumph) by admin on 28-10-2010

download
Under the tank on the left side of the bike, see Figure 03 & Figure 04, you will find a number of plugs, the one you are looking for looks like the one in Figure 02. FIGURE 02 FIGURE 03 FIGURE 04 Before separating the plug I tied a piece of string around the large plug because the cable from the sensor was not very long and I worked out I would need to pass the large plug over to the opposite side of the bike to get better access to change the plug to the one provided. Pull the plug apart and keep the small side on the left side of the bike. FIGURE 05 Then carefully feed the string through to the right side of the bike. Route the large plug and cable in such a manor that will give you the maximum length to allow ease of access to the plug. FIGURE 06 At this stage follow the instruction provided with the Speedo Healer to replace both large and small plugs. The existing plugs are very easily removed as per the instructions and can easily be reversed if required. Keep the plug, as per Figure 2, in a safe place so you can return the bike to it’s original state