Harley Davidson V-Rods Wide Wheel Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 13-04-2012

download
This instruction sheet is written with the assumption you will be replacing stock components. If the bike is already modified, some of the steps may be different. To install the PM PhatRod Kit it will be necessary to raise the motorcycle off the ground on a suitable lift. Installation of the PM PhatRod Kit begins with the disassembly and removal of the entire rear end of the bike. For additional detailed information on removal of these parts, consult your factory manual. Some of the original hardware will be reused, do not discard until complete. 1) Remove Seat (both front and rear sections) 2) Remove Turn Signal Canceling Module and Bracket. 3) Remove Outer Fender (remove all 6 bolts from top of fender and save hardware) 4) Disconnect taillight harness from lights (do not remove at this point) 5) Remove shocks (save the mounting nuts and washers from the top of shocks only). 6) Remove shocks and forward most bolts from inside of fender/struts 7) The entire inner fender/struts/taillight assembly should come off at this point. See Photo 4 8) Remove front splash guard Be sure to center the motorcycle on the lift so that it does not fall over when you raise it up or when you are working on it Disconnect the battery. Stock Component Removal W a r n i n g Photo 1 Photo 2 Photo 3 Photo 4 3

HARLEY DAVIDSON LEFT SIDE TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION NOTE While handling and installing tool box, be careful not to scratch surface. 1. See Figure 1. Attach the toolbox (4) to the toolbox mounting bracket (1) using the three pan head screws (2) and Nylock nuts (3) from the kit. 2. Remove the two button head screws (I) which secure left rear fender support (B) to motorcycle frame (C). Retain screws for reassembly. 3. On models with passenger footpegs: a. For FLSTN models: Remove button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E). b. For all other models: Remove the locknut (G), hex head bolt (J), spring washer (H) and footpeg (E). Remove the socket head cap screw (K) that secures the footrest support (F) to the frame (C). c. Remove the two bolts, nuts and washers which secure the bottom of the splash guard to the swingarm. This will allow you to move splash guard when installing the new passenger footrest bolt. d. Retain all removed components. 4. On models with passenger footboards: a. Remove the screw securing the passenger footboard assembly to the frame. Remove the footboard assembly. b. Retain all removed components. 5. Slide the top of mounting bracket (1) between rear fender support (B) and frame (C). Align top holes in bracket with fender support holes. Align lower bracket hole with footrest mounting hole in frame. Install the two screws (I), removed in Step 2, in fender support. Do not tighten screws at this time. Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) 6. On models with passenger footpegs: a. For FLSTN models: Install button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E) on top of the toolbox bracket (1). Tighten screw to 35-45 ft-lbs (47.5-61.0 Nm). b. For all other models: Refer to instructions in footpeg extension kit, Part Number 49352-00 for installation, and install the extention kit, footrest support and footpeg on top of the toolbox bracket (1). c. Install the two bolts, nuts and washers and secure the bottom of the splash guard to the swingarm. 7. On models with passenger footboards: a. Position footboard assembly, in the same orientation as removed, on top of tool box bracket. b. Install screw removed in Step 4. Tighten to 35-45 ft- lbs (47.5-61.0 Nm)

HARLEY DAVIDSON SOFT LOWER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
This kit fits 1980 and later Touring models equipped with engine guards. It does not fit with mustache engine guards INSTALLATION NOTE Soft lowers should not be used in temperatures above 55 degrees Fahrenheit. Engine cooling air flow will be affected and could lead to overheating and possible engine damage. 1. Apply a light coating of silicone grease to cavities of snaps prior to installing soft lowers on motorcycle. 2. See Figure 1. An opening is provided in the soft lowers for mounting highway footrests (1) to engine guard. If using footrests, mount within the opening to prevent buckling of splash guard fabric. 4. Remove adhesive liner from back of reflector. NOTE The ideal temperature should be at least 60° F (16° C) for proper adhesion of the reflectors. 5. Place reflector on fender and press firmly into position. 6. Let the adhesive cure for 24 hours at no less than 60° F (16° C). 7. Repeat steps for other reflector

Airtail Compressor Kit for Airtail Suspension System Installation Instructions

0

Filed Under (Tips and Review) by admin on 14-02-2011

download
installation • Following steps covers retro fits and new installations. * DENOTES RETRO FIT APPLICATION ONLY. Step 1 – Compressor 1. Jack the bike up and support it so that you can remove the rear wheel. Place your jack in an area that will not lift on the swingarm and leaves access to the space right in front of the front shock mounts. This is the area you will be installing the valve assembly into. 2. Relieve all pressure from the air shock- both “ride height” and “bottoming control” chambers must be drained of pressure. 3. Remove the seat and disconnect the battery. 4. Remove the rear wheel and ” splash guard ” (part number 60363-00) * Retro fit applications only. New applications go to #11 of Step 1. *5. Remove compressor from pivot shaft, disconnecting any airlines and wires from the compressor and solenoid. *6. Remove coil cover with switch housing and air release valves, being sure to disconnect all connections and airlines. *7. With compressor removed, remove the original solenoid valve (Fig. 1) and the 2 “T” fittings (Fig. 2) from the compressor mounting bracket. Figure 1 Figure 2 *8. Un-screw outlet valve from compressor and remove original airline (Fig. 3), being sure to not lose small o-ring around the end of airline. This will be used in the next step.

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL SPLASHGUARD INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

1. Refer to the appropriate Service Manual and remove the Maxi® fuse. 2. Refer to the applicable Service Manual and remove the rear wheel. 3. See Figure 1. Remove one screw (1) and stock splash- guard (2) from swingarm (3). 4. Remove the protective film from the new splashguard. 5. See Figure 4. Using two screws (4) and nuts (2), loosely install the H-clips to the back of the splash guard vertically as shown. 2 1 3 is04881 1. P-clamp 2. Splashguard 3. Raised bar of swingarm Figure 2. Install Splashguard -J04271 1 of 2 1 3 2 4 5 is04892 1. H-clip 2. Swingarm 3. Splashguard 4. Screw 5. Nut Figure 3. H-Clips Installed on Swingarm 6. See Figure 2. Slide two P-clamps (1) around the upper bar of the rear fork. The straight side of the clamp will face rearward, as shown in Figure 4. 7. See Figure 4. Orient the splashguard with the polished side facing the rear wheel. Align the upper two holes with the P-clamp holes. Secure splashguard to the P-clips with two screws (4) and locknuts (2). Do not tighten at this time. 8. See Figure 3. Turn H-clips (1) horizontal on the splash- guard. Press splashguard (3) into place. When the splashguard is in place, rotate the H-clips down over the raise bar of the swingarm (2). Tighten the screw (4) and nut (5) to secure the H-clips. NOTE If adequate clearance does not exist between the splashguard and rear brake line and drive belt, adjust fender extension by loosening hardware and centering the splashguard. 9. See Figure 4. Ensure the splashguard does not touch the drive belt on the left side and the rear brake line on the right side, then tighten P-clip mounting screws (4) and nuts (2) securely. 10. Refer to the applicable Service Manual and install the rear wheel. 11. Refer to the appropriate Service Manual and install the Maxi fuse