harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

Honda GL1000/1100 starter motor Removal/ Over haul Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
1. Remove the three long bolts that hold the sections together and separate them. Be careful as there are a series of flat thrust washers on each end of the armature (located in the middle section). 2. The end cap basically performs no function other than to cover the brush plate and commutator area as well as center the armature shaft in a pressed in bushing located in the end of the cap. 3. The drive end contains the reduction gearing and if need be, can be disassembled to replace the bearing. This is extremely unlikely. The shaft should turn freely and normally only requires a cleaning and grease application. If the bearing in fact needs replacing, simply remove the “C” clips on either end, drive out the bearing and reinstall with an appropriate size replacement. Any decent auto parts / industrial supply should be able to supply the correct bearing. 4. Remove the brush plate from the end of the center section by removing the screw at the one brush connection. Before removing the brushes, note that one of them has an insulating sleeve over the braided wire. The replacement must go in the same brush holder. Remove the brushes and replace if necessary and clean the brush plate. ** Brake Cleaner is a good general cleaner for this entire job. 5. Remove the thrust washers from brush plate end of the armature. Count them and ensure they go back on the correct way. 6. The end of the center section that had the drive end on it has a circular plate covering it with a short splined shaft protruding through the plate. Drive the plate out by tapping the opposite end of the section on the shaft – just lightly with a rubber hammer or piece of wood to protect the shaft. Once the plate is out, remove the armature from the section. You will find more thrust washers at this end. Make sure they go back on correctly. 7. In the center of the center section there are four large Philips screws. These hold in the field coils found within the housing. Using an “impact driver”, loosen the four screws that go around the circumference of the center section and remove them. Remove the 10mm nut for the battery connection and the accompanying fiber insulating washers. With the screws and nut removed, the entire field coil assembly should withdraw entirely from the housing. There will be four (4) metal plates that the screws mounted into come falling out. They are easily replaced into the field coils when you slide it back into the housing. Do not be alarmed that you suddenly have four loose metal parts. 8. With everything out of the housing, thoroughly clean everything using the Brake Cleaner. Although the cleaner will dry without leaving a film, it is suggested that the components be dried with compressed air. 9. Get some extremely fine steel wool (“000″ of even “0000″ is better) and gently clean the metal surfaces or bars of the armature and the commutator. Blow with compressed air. 10. Using a volt/ohmeter, test for continuity between pairs of armature bars (the long ones). There should be continuity between the pairs around the entire circumference.

HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON SCREAMIN’ EAGLE BILLET CAM SUPPORT PLATE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL NOTE For removal, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove the Maxi┬« fuse. 2. Remove the cam cover and gasket. 3. Remove and discard the crank and primary cam sprocket flange bolts and washers. 4. Release the oil pump, and remove the cam support plate and cams. Disassemble the cams from the support plate and discard the support plate. 5. Inspect cams, chain, sprockets, oil pump, chain tensioners and guide for wear and replace as needed. Refer to the Service Manual for inspection and replacement proce- dures. -J04503┬áINSTALLATION NOTES For installation, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. See Figure 1. When installing Screamin’ Eagle camshaft kits, install the O-ring included in this kit over the splined shaft of the rear camshaft as shown. 1. Using the Camshaft Assembly Tool (HD-47956) and assemble the camshafts, chains and tensioners to the billet cam support plate. 2. Install the cam support plate assembly into the crankcase. 3. Using the Crankshaft/Camshaft Locking Tool (HD-47941), install cam sprockets, chain and tensioner. 4. Install cam cover and gasket. 5. Install Maxi fuse.

HARLEY DAVIDSON SPORTSTER FORWARD CONTROL KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 6. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is03193 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw (2) Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is03194 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove the exhaust to access the brake rod. Follow the instructions in the appropriate Service Manual. 3. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod INSTALLATION Install Forward Control Brake Pedal and Footrest Assemblies 1. See Figure 5 and Figure 6. At the lower front of the right frame downtube, remove the two screws securing the J- clip (B) to the frame. Discard the screws but save J-clip for installation. 2. Install the other end of the brake rod into the brake pedal assembly (8). Tighten to 84-144 in-lbs (9.5-16.3 Nm) . NOTE Assemble the brake pedal and footpeg clevis onto the footrest support bracket (as described in the next step) prior to mounting the support bracket to the frame. This will allow easier installation of the footrest mount clevis retaining ring (installed to grooved end of footrest mount clevis). 3. Slide the brake pedal (8) onto footrest mount clevis (11) then slide clevis into footrest/brake pedal support bracket (9). Align hole in the clevis with hole in the support bracket and install screw (6). Tighten the screw to 18-22 ft-lbs (24.4-29.9 Nm) . 4. Install the footrest mount clevis retaining ring (18) to the groove at the end of the footpeg clevis. 5. Position the J-clip (from Step 1) against the frame aligning the mounting holes. Mount the footrest/brake pedal support bracket (9) and J-clip to frame using the new screws (3). Tighten the bracket to 45-50 ft-lbs (61.1- 67.9 Nm) . 6. Obtain the brake rod (15) from kit and thread one end into the master cylinder bell crank. Tighten to 120-180 in-lbs (13.6-20.3 Nm) . 7. Install footpeg on clevis with spring washer (2). Make sure spring washer is positioned inside clevis (11) with the square edge toward the inside. Align holes and push clevis pin (7) from top down through hole in clevis. Secure clevis pin using the new retaining ring (17). 8. Install exhaust following the instructions in the appropriate Service Manual. Install Forward Control Shift Lever Assembly

Related Item : ttr 125 frame cradle (2)sportster brake pedal pivot shaft install forward controls (2)transalp footrest lowering kit m and p direct (1)tao tao 150 left foot rest (1)psr frame slider installation (1)monoshock harley frame (1)footrest for dyna (1)cotter pin proper installation mopar (1)change clevis on ohlins (1)bolt on mono shock racing frame for harley (1)