MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

Steering Stem Nut Installation Instructions & Owners Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
Sport Bike Damper Kit Installation Instructions DISCLAIMER: All GPR Sport Bike damper kits are manufactured to be used ONLY w/ the stock top triple clamp and frame. If either is modded, aftermarket or crash damaged, the kit will not install properly and GPR will not be held responsible for the consequences of improper installation due to this or any other improper mounting or modifying. The provided instructions must be followed precisely, as failure to do so can result in the GPR damper kit being installed incorrectly. An improper installation may lead to a variety of undesirable steering problems. Please take your time and carefully follow the installation instructions. As always, give us a call if you have any questions, we’re more than happy to assist you in getting the damper kit mounted on your bike properly 1. Remove the stock Steering Stem Nut (SSN) and washer from the stock top triple clamp steering stem. Carefully set the stock nut aside, as you may be using it later. Bikes requiring a specific GPR SSN to replace the stock SSN are listed at the end of this installation sheet. If your bike is on the chart, throw you stock SSN in the toolbox along w/ the washer, as you may need it at a later date if for any reason you need to remove the GPR kit from your bike. Stock SSN’s that are either ‘domed’ at the top or ‘flanged’ at the bottom will definitely NOT work, may lead to problems and should NOT be reinstalled during the baseplate installation. See #2 below for further instructions about both SSN/Steering stem and arm clearance issues 2. With the stock SSN and washer removed, place the GPR Baseplate over the steering stem on the top triple clamp and reinstall either the stock SSN or the GPR SSN provided. Torque SSN down to the recommended specs as per the owner’s manual for your particular bikes make and model. NEVER reinstall the stock washer that came on the bike! The baseplate is now your new washer. If you do accidentally use the stock washer, the arm on the stabilizer will most likely ‘rub’ on the nut. It will be too high, potentially locking the steering and handlebars, thus making your bike un steerable and unridable. DO NOT ride your bike until all installation steps have been completed and you can visually verify that there is clearance between the arm of the stabilizer and the steering stem and/or SSN. Once the installation is complete, at the #1 setting you

Incoming search terms: