Suzuki GSX1000R 465 SeriesSingle Shock Supplement

0

Filed Under (Suzuki) by admin on 13-02-2011

download
1. One set of the shouldered sleeves with O-rings should be installed in the shock eye. If not, insert sleeves with O-rings in the shock eye (see figure 1). 2. Mount the shock as you would your stock shock per your authorized shop manual noting the following; Make sure the shock is mounted with the rebound adjustment at the bottom and facing the right side of the motorcycle and the nitrogen pressure valve is facing forward. Tighten the shock bolts to the proper torque specifications (refer to your manual). Caution: The installed spring length must never be set shorter than 133mm (5.25″) or shock damage may occur

KTM WP FORK 4860 MXMA CLOSED CARTRIDGE REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 22-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms: