Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

1984 KAWASAKI GPz900R Restoration Project

0

Filed Under (Kawasaki) by admin on 01-12-2010

download
The paint work on the motorcycle is the original “Red & Gun Metal Grey” but is so badly worn with the outer layer of clear missing and hence all body work requires re-painting. The tank has undergone the usual repair on the left hand side since rust has eaten into the bottom corner from water being in the fuel and the paint has been worn of where the riders legs rub.. The rear tail piece is structurally ok but features worn paint. The right hand side cover has a broken stud and the left hand side cover has a heat warp under the tank. The lower fairing is damaged, the middle fairing is missing one decal on the right hand side and the top fairing has small cracks from a possible accident. The wind screen is worn and faded and will require replacement. The seat has been taped together and requires recovering. Figure 1 Body Work in original state. 1984 GPz900R Schedule of Work 4 of 20 1.2.2 Engine The engine has 90,000 klms on it according to the instruments which appear to be original. The engine was sold with a defective starter clutch as it appears to spin but initial attempts to start the engine failed. A replacement starter clutch is in storage and to refit the part requires that the engine be removed, inverted, bottom engine case removed and all assemblies removed until the starter clutch become accessible rather than a total rebuild. The engine was last run in 2005 and appears to be in good external condition. The condition of the carburetors is unknown but will need to be stripped and cleaned as a service exercise. 1.2.3 Suspension and Brakes On arrival a rust spot with a diameter of 5 cm was noted on the left fork and it was determined that the forks must undergo hard chroming to remove the rust and any chips. The fork seals are damaged but replacements have been supplied. An inspection of the disks revealed worn disks front and rear. New disks are available and will be required. The condition of the brakes appears to be poor but for a bike that has had no services performed this is to be expected. The image below shows the state of the motorcycle at time of purchase

YAMAHA FZS 600 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-11-2010

download
CHECKING THE CONNECTIONS Check the leads, couplers, and connectors for stains, rust, moisture, etc. 1. Disconnect: lead coupler connector 2. Check: lead coupler connector Moisture Dry with an air blower. Rust/stains Connect and disconnect several times. 3. Check: all connections Loose connection Connect properly. If the pin 2 on the terminal is flattened, bend in up. 4. Connect: lead coupler connector Make sure that all connections are tight. 5. Check: continuity (with a pocket tester) Pocket tester 90590-03112 If there is no continuity, clean the termi- nals. When checking the wire harness, perform steps 1 to 3. As a quick remedy, use a contact revitaliz- er available at most part stores.
1-5 GEN INFO SPECIAL TOOLS 1 2 1 2 1 2 1 EB104000 SPECIAL TOOLS The following special tools are necessary for complete and accurate tune-up and assembly. Use only the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools or improvised techniques. When placing an order, refer to the list provided below to avoid any mistakes. Tool No. Tool name/Usage Illustration 90890-01268 Ring nut wrench This tool is used to loosen and tighten the steering ringnut. 90890-01304 Piston pin puller This tool is used to remove the piston pin. 90890-01460 -01326 Damper rod holder T-handle These tool ar used for holding the damper rod when removing or installing the damper rod. 90890-01312 Fuel level gauge This gauge is used to measure the fuel level in the float chamber. 90890-01325 -01352 Radiator cap tester Adaptor These tools are used for checking the cooling system. 90890-01362 -01382 Flywheel puller Crank shaft protector These tools are used for removing the rotor and starter clutch. 90890-01367 -01381 Fork seal driver weight Fork seal driver attachment (ø41 mm) These tools are used when installing the forkseal.

Incoming search terms: