YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

Yamaha XVS 650AN Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 15-12-2010

download
MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Connecting rod: Oil clearance Color code (corresponding size) 0.031 0.055 mm (0.0012 0.0022 in) Blue Black Brown Green CHASSIS Item Standard Limit Front suspension: Front fork travel Fork spring free length Installed length Spring rate (K1) Stroke (K1) Optional spring Oil capacity Oil level Oil grade 140 mm (5.5 in) 332.5 mm (3.1 in) 287.4 mm (11.3 in) 3.43 N/mm (0.343 kg/mm, 19.2 lb/in) 0 140 mm (0 5.5 in) No 0.507 L (17.4 US oz) 95 mm (3.74 in) Yamaha fork oil 10 WT or equivalent 325.9 mm (12.83 in) Front brake: Type Disc outside diameter thickness Pad thickness inner Pad thickness outer Master cylinder inside diameter Caliper cylinder inside diameter Caliper cylinder inside diameter Brake fluid type Single disk 298 5 mm (11.73 0.2 in) 6.0 mm (0.24 in) 6.0 mm (0.24 in) 14.0 mm (0.55 in) 30.2 mm (1.19 in) 33.3 mm (1.31 in) DOT 4 4.5 mm (0.18 in) 0.8 mm (0.03 in) 0.8 mm (0.03 in) Brake lever & brake pedal: Brake lever free play (at pivot) Brake lever free play (at lever end) Brake pedal position Brake pedal free play Clutch lever free play (at pivot) Clutch lever free play (at lever end) 1 2 mm (0.04 0.08 in) 10 15 mm (0.39 0.59 in) 108 mm (4.25 in) 20 30 mm (0.79 1.18 in) 2 3 mm (0.08 0.12 in) 10 15 mm (0.39 0.59 in) -4- MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit T.C.I.: Pickup coil resistance/color T.C.I. unit model/manufacturer 182 222 Ω at 20C (68F)/Gray – Black J4T088/MITSUBISHI (U.S.A) J4T128/MITSUBISHI (CAL) Ignition coil: Model /manufacturer Minimum spark gap Primary winding resistance Secondary winding resistance F6T541/MITSUBISHI 6 mm (0.24 in) 3.6 4.8 Ω at 20C (68F) 10.7 14.5 kΩ at 20C (68F) Voltage regulator: Type Model /manufacturer No load regulated voltage Semi-conductor, short-circuit type SH650C-11/SHINDENGEN 14.1 14.9 V Rectifier: Model /manufacturer Capacity Withstand voltage SH650C-11/SHINDENGEN 18 A 200 V Electric starter system: Type Starter motor: Model /manufacturer I.D. number Output Brush overall length Commutator diameter Mica undercut Starter relay: Model /manufacturer Amperage rating Constant mesh type SM-13/MITSUBA SM-13 0.7 kW 10 mm (0.39 in) 28 mm (1.10 in) 0.7 mm (0.08 in) MS-5F-441/JIDECO 180 A 4 mm (0.16 in) 27 mm (1.06 in) Flasher relay: Type Model /manufacturer Self cancelling device Flasher frequency Wattage Semi transistor type FB257H/DENSO Yes 75 95 cycle/min 27 W 2 + 3.4 W Fuel pump relay: Model /manufacturer G8R-30Y-Q/OMRON

HARLEY-DAVIDSON BIG TWINS COMPUFIRE 1084 GEAR SETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
1. Remove the seat and disconnect the cables at the battery. Remove the ground cable first and then the positive (+) cable. 2. Drain the oil in the outer primary case and remove the outer primary cover following instructions in the Factory Shop manual. 3. Bend the tab on the jackshaft bolt away from the bolt head. Remove the starter pinion gear with the jackshaft bolt, lock plate and washer. 4. Remove the clutch assembly using the procedure found in the Factory Shop manual. 5. Remove the original equipment ring gear from the clutch basket by drilling out the rivets with a 5/16-inch drill bit. Drill through the rivet head and tap the ring gear off the clutch basket using a hammer. 6. Drill out the six holes in the clutch basket with the 5/16-inch drill bit. RING AND STARTER PINION GEAR INSTALLATION 1. Attach the new 84-tooth ring gear to the clutch basket using the six 5/16×24 socket head cap screws supplied. NOTE… The bevel side of the ring gear (identified by the three dots) faces away from the starter motor. Torque the socket head cap screws to 29 ft lbs. 2. Assemble and install the primary drive assembly following the instructions in the factory Shop manual. 3. Install the new 10-tooth pinion gear with the jackshaft bolt, lock plate and thrust washer. Torque the jackshaft bolt to 7 – 9 ft lbs. Bend the lock tab on the lock plate against a flat on the jackshaft bolt head. 4. Measure and adjust the air gap between the ring gear and the pinion gear. See Fig-1 . The correct gap is .075 – .125 inch. If the gap is larger than .125 inch, use the supplied shim washers inside the jackshaft coupler. See Fig-2 . If the air gap is smaller than .075 inch, the jackshaft must be shortened by removing material from the splined end of the shaft. See Fig-3 . 5. Install the outer primary cover following instructions in the Factory Shop manual and refill the primary case with the proper amount of primary oil. 6. Re-install the battery cables in the reverse order they were removed. Re-install the seat

Incoming search terms:

COMPUFIRE 1084 GEAR SETS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
1. Remove the seat and disconnect the cables at the battery. Remove the ground cable first and then the positive (+) cable. 2. Drain the oil in the outer primary case and remove the outer primary cover following instructions in the Factory Shop manual. 3. Bend the tab on the jackshaft bolt away from the bolt head. Remove the starter pinion gear with the jackshaft bolt, lock plate and washer. 4. Remove the clutch assembly using the procedure found in the Factory Shop manual. 5. Remove the original equipment ring gear from the clutch basket by drilling out the rivets with a 5/16-inch drill bit. Drill through the rivet head and tap the ring gear off the clutch basket using a hammer. 6. Drill out the six holes in the clutch basket with the 5/16-inch drill bit. RING AND STARTER PINION GEAR INSTALLATION 1. Attach the new 84-tooth ring gear to the clutch basket using the six 5/16×24 socket head cap screws supplied. NOTE… The bevel side of the ring gear (identified by the three dots) faces away from the starter motor. Torque the socket head cap screws to 29 ft lbs. 2. Assemble and install the primary drive assembly following the instructions in the factory Shop manual. 3. Install the new 10-tooth pinion gear with the jackshaft bolt, lock plate and thrust washer. Torque the jackshaft bolt to 7 – 9 ft lbs. Bend the lock tab on the lock plate against a flat on the jackshaft bolt head. 4. Measure and adjust the air gap between the ring gear and the pinion gear. See Fig-1 . The correct gap is .075 – .125 inch. If the gap is larger than .125 inch, use the supplied shim washers inside the jackshaft coupler. See Fig-2 . If the air gap is smaller than .075 inch, the jackshaft must be shortened by removing material from the splined end of the shaft. See Fig-3 . 5. Install the outer primary cover following instructions in the Factory Shop manual and refill the primary case with the proper amount of primary oil. 6. Re-install the battery cables in the reverse order they were removed. Re-install the seat

Incoming search terms:

SUZUKI VX800 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 25-11-2010

download
DIMENSIONS AND DRY MASS Overall length ………………………… 2280 mm (89.8 in) . . . E15, 16, 17, 22, 25, 39 2355 mm (92.7 in) . . . El8 2255 mm (88.8 in) . . . Others Overall width ………………………… Overall height ………………………… Wheel base …………………………… 805 mm (31.7 in) 1115 mm (43.9 in) . . . E03, 28,33 1085 mm (42.7 in) . . . Others 1565 mm (61.6 in) . . . E03,33 1555 mm (61.2 in) . . . Others Ground clearance ……………………… Seat height ………………………….. Dry mass …………………………… 145 mm ( 5.7 in) 800 mm (31.5 in) . . . EOI, 03, 28,33 795 mm (31.3 in) . . . Others 214 kg (472 Ibs). . . E33 213 kg (470 Ibs) . . . Others ENGINE Type ………………………………. Valve clearance ……………………….. Number of cylinders. …………………… Bore ………………………………. Stroke …………………………….. Piston displacement ……………………. Compression ratio …………………….. Carburetor, Front. …………………….. Rear ……………………… Air cleaner ………………………….. Starter system ……………………….. Lubrication system …………………….. Four-stroke, water-cooled, OHC, TSCC, 45″ V-twin 0.08 – 0.13 mm (0.003 – 0.005 in) 2 83.0 mm (3.268 in) 74.4 mm (2.929 in) 805 cm3 (49.12 cu. in) 10.0 : 1 MI KUN I BDS36SS, single MI KUN I BS36SS, single Polyester fiber element Electric starter motor Wet sump TRANSMISSION Clutch …………………………….. Transmission ………………………… Gearshift pattern ……………………… Primary reduction ratio …………………. Gear ratios, Low ……………………… 2nd ………………………. 3rd ………………………. 4th ………………………. Top ……………………… Secondary reduction ratio ……………….. Wet multi-plate type 5-speed constant mesh 1 -down, 4-up 1.690 (71/42) 2.285 (32/14) 1.631 (31/19) 1.227 (27/22) 1 .OOO (25/25) 0.851 (23/27) 1.133 (17/15x 30/30) . . . E03,33 1.096 (17/15x 30/31) . . . Others 3.090 (34/l 1) Final reduction ratio …………………… Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shaft drive

MOTO GUZZI Quota 1100 ES Specifications And Owner's Manual

0

Filed Under (Moto Guzzi) by admin on 25-11-2010

download
Engine 4-stroke, twin cylinder Cylinder configuration: 90° V-twin Bore: 9 2 mm Stroke: 80 mm Capacity: 1064 cc Compression ratio: 9.5:1 Max. torque: Nm 85 (kgm 8.7) at 3,800 rpm Max. power: Kw 51 (CV 70) a 6,400 rev/min Timing system With rods and rockers and 2 valves per cylinder. One camshaft in the crankcase driven by duplex chain with automatic chain tensioner. Feed system Indirect electronic injection, timed sequential MAGNETI MARELLI IAW 15M “Alfa-N” system, single throttlebody, Weber IW031 injectors, electric pump with pressure regulator, digital control of optimized injection times. Lubrication Pressure fed by gear pump. Wire mesh and cartridge filters on oil sump. Normal lubrication pressure 3.8÷4.2 kg/cm2 (pressure valve on oil sump). Low oil pressure sensor (electrical) on crankcase. Generator / Alternator On front of crankshaft. Output power: 350W at 5000 rev./min. (14V – 25A). Ignition “MAGNETI MARELLI” Inductive discharge digital electronics. Spark plugs: NGK BPR 6 ES. Spark plug gap: 0.7 mm 2 ignition coils Starter Electric starter motor 12V-1.2 Kw with electromagnetic ratchet control. Ring gear on the flywheel. START « » push-button on right handlebar. Transmission Clutch Dry, twin driven plates. Located on engine flywheel. Clutch lever on left handlebar. Primary drive With helical gears, 1:1.3529 (Z=17/23). Gearbox 5-speed, front engaging, constant mesh. Incorporated Cush drive Control pedal on left side of machine. Gear ratios: 1st 1:2 (Z=14/28) 2nd 1:1.3158 (Z=19/25) 3rd 1:1 (Z=23/23) 4th 1:0.8462 (Z=26/22) 5th 1:0.7308 (Z=26/19) Final drive Cardan shaft with gears Ratio: 1:4.125 (Z=8/33) Overall gear ratios (engine-wheel) 1st gear = 1: 11.1618 2nd gear = 1: 7.3433 3rd gear = 1: 5.5809 4th gear = 1: 4.7223 5th gear = 1: 4.0783 Frame Double steel rectangular bar with double cradle

Incoming search terms:

BMW F 650 CS Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Connection 11 Engine Freewheel housing and freewheel Nm 35 (clean thread + Loctite648) Engine block Nm 10 Double drive gear on crankshaft Nm 180 (clean thread + Loctite243) Driver to countershaft Nm 140 (clean thread + Loctite243) Pressure plate Nm 10 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Chainwheel to main shaft Nm 140 (clean thread + Loctite243) Signal transmitter Nm 8 Ignition cover Nm 10 Cylinder base Nm 10 Fastener for chain tensioner Nm 40 Oil circuit Oil filter cover Nm 10 Oil pressure switch Nm 12 (clean thread + Loctite243) Strainer cover to housing half Nm 8 Drain plug, on-frame oil tank Nm 21 Engine oil drain plug Nm 40 Oil supply/oil return lines to engine Nm 42 Oil pump cover Nm 6 (clean thread + Loctite243) Oil pressure valve Nm 24 Oil retaining valve Nm 24 Cylinder head Collar nuts for cylinder head Nm 60 Collar screws for cylinder head Nm 33 Machine screws (chaincase) Nm 10 Camshaft bearing cap Nm 10 Chain sprockets to camshafts Nm 60 threads oiled Chain guide to camshaft bearing cap Nm 10 (clean thread + Loctite243)
00.4 Cylinder head cover Nm 10 Machine screw (hole for locating screw) Nm 25 Model F 650 CS Connection 12 Engine electrics Spark plug Nm 20 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Signal transmitter Nm 8 Engine block cover, left/right Nm 10 Starter to clutch cover Nm 10 Positive lead to starter motor Nm 9 Positive contact to starter motor Nm 4 Necked-down bolt, starter housing Nm 6 Cable cover to engine block Nm 9 Cable holder to ignition cover Nm 8 Stator to ignition cover Nm 10 (clean thread + Loctite243) Ignition coil bracket to cylinder head cover Nm 9

Incoming search terms:

2008 HARLEY-DAVIDSON FXCW Softail Rocker Specifications

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
Three-phase, 38-amp system ………………………………………. (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting……………….. 1.2 kW electric with solenoid shift starter motor engagement Lights (as per country regulation): Headlamp ……………….. Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop ghts……………………………………………………………….. Integrated LED Turn Signal Lights ……………………………………………………… 21W self-canceling Instruments …………………. Tank-mounted electronic speedometer with odometer; ………………………………………………… Time-of-day clock; Dual resettable tripmeter Indicator Lamps …………………… High beam, neutral, low oil pressure, turn signals, ………………………………………………………….. engine diagnostics, security system6, ……………………………………………………………………….. 6-speed, low fuel warnings Colour Options7 Vivid Black; Pacific Blue Pearl; Crimson Red Sunglo Model Features Silver powder-coated engine; Custom finned cast aluminium “horseshoe” oil tank with chrome external oil lines; Painted, stretch low profile tank console; Fire-truck inspired bullet headlamp; Bullet style LED turn signals; Adjustable, V-bar riser; Forward-mounted rider footpegs; Stainless steel, pull-back, internally-wired handlebars; Lowest seat height of all Harley-Davidson® motorcycles Warranty Warranty8 ……………………………………………………… 24 months (unlimited mileage) Service Interval9 ………………………………………………. First 1,000 miles (1,600 km), ………………………………………………………. every 5,000 miles (8,000 km) thereafter Dimensions

2007 Harley-Davidson Softail Family Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
frame Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Swingarm Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Front Fork 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers Rear Shocks Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Caliper Type 4-piston front and rear 4-piston front and rear 4-piston front and rear Rotor Type: (diameter x width) Patented, uniform expansion rotors Patented, uniform expansion rotors Patented, uniform expansion rotors Front 292 mm x 5.08 mm 292 mm x 5.08 mm 292 mm x 5.08 mm Rear 292 mm x 5.84 mm 292 mm x 5.84 mm 292 mm x 5.84 mm Front (mm) 130 130 130 Rear (mm) 109 109 109 Engine Torque (EU standard EC95/1)5 86 ft. lb / 117 Nm @ 3200 rpm 89 ft. lb / 120 Nm @ 3300 rpm 89 ft. lb / 120 Nm @ 3300 rpm Right 29° 30° 28° Left 26° 28° 26° Battery Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating ) Charging Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement Headlamp Headlamp Headlamp Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop Lights Tail/Stop Lights Tail/Stop Lights 8W/28W (5W/21W) 8W/28W (5W/21W) 8W/28W (5W/21W) Turn Signal Lights Turn Signal Lights Turn Signal Lights 28W (21W) self-canceling 28W (21W) self-canceling 28W (21W) self-canceling Indicator Lamps Indicator Lamps Indicator Lamps High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6- speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings Passing Lamps Chrome Vivid Black Vivid Black Vivid Black Black Cherry Pearl Black Cherry Pearl Black Cherry Pearl Deep Cobalt Pearl Black Pearl Black Pearl Pewter Pearl Fire Red Pearl Deep Cobalt Pearl White Gold Pearl Deep Cobalt Pearl Olive Pearl & Vivid Black Suede Blue Pearl & Vivid Black Suede Blue Pearl White Gold Pearl & Vivid Black Black Cherry Pearl & Pewter Pearl Olive Pearl White Gold Pearl & Deep Cobalt Pearl Fire Red Pearl & Black Pearl Pacific Blue Pearl Deep Cobalt Pearl & Pewter Pearl Pewter Pearl Yellow Pearl White Gold Pearl

Incoming search terms:

BMW K 1100 LT/ RS Repair And Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
Transmission cover to transmission 9 Machine screw for neutral stop 13 Stud bolt, selector shaft 17 (Loctite 243) Transmission to intermediate flange 16 Frame mounting to transmission 45 Bearing mount to transmission 41 (Loctite 243) Starter motor to transmission 9 Positive lead to starter motor 5 Fixed bearing of swinging arm to transmission 9 Swinging arm bearing journal (loose bearing) 7,5 Locknut of bearing journal 41 Fixed bearing rear wheel drive in swinging arm 150 (clean thread + Loctite 2701) Bearing pin, loose bearing rear wheel drive in swinging arm 7 (clean thread + Loctite 2701) Locknut, loose bearing rear wheel drive in swinging arm 105 (clean thread + Loctite 2701) Suspension strut to frame/rear wheel drive 51 Brake caliper 32 Hinterradschraub en 105 Exhaust to cylinder head 21 Silencer to holder/footrest plate 9 Front silencer to transmission 12 Footrest plate to transmission 15 31 Front fork Oil filler plug 10 Oil drain plug 3,5 Spring support bearing 20 Locking tube 65 Hexagon nut 65 Clamping screws of fork bridges 15 Bottom screw fitting 47 Handlebar clamp block 22 Fork stabilisor

Incoming search terms: