HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

EVO 3-Phase Charging System Installation And Owner's Manual

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
install rotor onto sprocket shaft and seat against rotor spacer 9. Install the compensator extension shaft on the sprocket shaft 10. Using your motorcycle’s specific repair manual instructions, check for proper chain alignment. Use OEM-specified shims to bring chain alignment into specification if required. 11. Using your motorcycle’s specific repair manual instructions, install the primary drive and clutch. Assure that all driveline components line up correctly. 12. Apply Loctite Threadlocker #262 (“red”) to the threads of the sprocket nut (also supplied with compensator shaft extension kit). Tighten sprocket nut to 150-165 ft-lbs (203.4-223.7 Nm). 13. Using your motorcycle’s specific repair manual instructions, install the primary cover. 14. Connect the negative battery cable. 2.3 Factory Regulator Removal 1. Disconnect the negative battery cable. 2. Using your motorcycle’s specific repair manual instructions, remove the regulator. Save the factory-supplied hardware. 2.4 3-Phase Regulator Installation 1. Connect the 3-pin stator connector to the regulator. 2. Using the factory-supplied hardware, locate the 3-phase regulator on the mounting bracket and install using the factory-supplied hardware. Tighten to 50-80 in-lbs. 3. Attach the ground wire between the bracket mounting bolt and the bracket. Tighten to 70-100 in-lbs. 4. Trial-fit the long power wire to the motorcycle, and route to the original location of the factory regulator wire on the circuit breaker. 5. Trim any excess wire, and strip 5/16″ of insulation from the end of the wire using a wire stripper. 6. Slip the 1″ length of heat shrink (supplied) onto the wire. 7. Crimp on the (supplied) ring lug to the end of the wire, taking care that a good crimp connection is made.

XR 600 Dual Sport Kit Installation Manual

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the side panels, seat, and gas tank. 3. Unplug the headlight and taillight from the stock wiring and remove. 4. Locate the AC voltage regulator mounted on the left side of the frame backbone, (Fig.1) unplug from wiring harness, and remove the regulator. This regulator is located above the air box on ’87 and earlier XR 600′s and 500′s. AC Regulator (Remove) Pulsar Coil Alternator (Stator) Wiring Alternator (Stator) Contains both exciter coil and lighting coils Figure 1: If you are colorblind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 5. A three wire group consisting of a black/red wire, a green wire, and a white/yellow wire (may appear light gray/yellow) are the output leads from the stator. 1990 and earlier models only have two wires coming up from the alternator, a black/red wire and a blue wire. On 1991 – 1999 XR 600′s, unplug the green wire and the white/yellow wire. (This should have already been done 3 when you removed the voltage regulator in Step 4.) On 1990 and earlier XR 600′s see the Stator Modification Instructions enclosed. 6. Temporarily disconnect the black/red wire and remove the rubber boot that shields the wire bundle. Reconnect the black/red wire making sure that it plugs in tightly, as this lead is responsible for powering the bike’s ignition. 7. Voltage Regulator Installation: The voltage regulator/rectifier mounts to the top right rear corner of the air box (Photo 1). Use the template provided to determine the location at which to drill the two 1/4 inch mounting holes in the air box lid. The outside edge of the regulator should be nearly flush with the outside edge of the air box when mounted properly.

Pulsar XR 650R ELECTRIC-START KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Remove the seat, fuel tank, side panels, muffler, and headers. 2. Disconnect the stator wires from their corresponding mates underneath the seat (trace the wires up from the left side case.) Un-route the stator wiring so it hangs free from the left side case. 3. Remove the stock shift lever and the left side engine case cover. You do not need to drain the oil from the engine. 4. Unbolt and remove the stator and wiring from the stock cover. Do not cut any wires. 5. The stock pulsar coil (small black box hanging from the stator) will have to be modified slightly to clear the ring gear before installation into the new cover. Remove (file or grind) about .030 inches of material from the base of the pulsar coil so that the base is flush with the face of the rest of the coil as shown in Photos 1 and 2. File Here Photo 2 Make flush with this surface Remove material here Photo 1 6. Install the stator and modified pulsar coil into the new engine case cover as shown in Photo 3. Use the three provided Phillips head bolts, split lock-washers, and plastic cable clamps to secure the wiring as shown. You will need to pull about ½” of extra wire through the grommet (Photo 4) to give you enough wire length for the grommet to sit in its case cutout. To do this, remove the electrical tape from the end of the stator wires and pull each wire individually through the grommet. Neither of the stock metal wire guides will be used when reinstalling the stator into the new case (Photo 5). 5/16″ cable clamps 1/8″ cable clamp Photo 3 Photo 5 Not Used Pull extra wire through grommet Photo 4 7. Remove the stock flywheel nut (An air impact tool works best to remove this nut without turning the motor). Remove the flywheel using the flywheel puller provided. 8. Locate the T and F marks on the stock flywheel (Photo 6). The T mark is used to adjust valve clearances and its location needs to be transferred to the ring gear. Scribe a line in the edge of the flywheel in line with the T mark as shown in Photo 7

Incoming search terms: