SUZUKI VZ800 MARAUDER SLIP-ON EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe right hand side footrest assembly. 2. Loosenthe two head pipes at the cylinder head. 3. Loosen the muffler clamps, located on the inlet end of the mufflers. 4. Remove the two nuts that mount the lower muffler to motorcycle. Keep the two mufflers bolted together as an assembly. 5. Lift the muffler assembly up to clear the studs from the mounting holes. Pull the mufflers off the head pipes and set them aside. 6. Remove the two flanged steel spacers from the hole in the rubber cushions, where the stock muffler assembly mounted. Reinstall the steel spacers through the backside of the rubber cushions so the flanged end of the spacers are on the backside of the cushions, opposite of there original position. 7. Remove the rear most heat shields from both of the head pipes and set them aside. 8. Remove the stock exhaust gaskets from the ends of both pipes. The Vance & Hines slip-on does not use a gasket at the slip joint . 9. Install the new muffler mounting bracket (stamped with the # 233 ) to the front side of the two holes with the rubber cushions the two of the 5/16″x 1 1/4″ bolt and two 5/16″ lock nuts (hardware supplied) through the two holes in the bracket that are spaced farthest apart. When mounted correctly, the bracket should bend up and out from the motorcycle

Incoming search terms:

HONDA SHADOW ACE TOURER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the pinch clamp bolt on the left hand muffler crossover pipe. (Located on the right of the motorcycle, where both mufflers merge with the head pipes). 2. Remove the two 8mm bolts that mount the left hand muffler to the frame. Drop the muffler down to clear the mounts and pull out from the collector. 3. Remove the right hand frame cover to avoid damaging it. 4. Remove the 8mm nut holding the head pipe flanges to the cylinder heads. Remove the 8mm bolts that mount the right hand muffler to the frame. 5. Remove the remainder of the exhaust system from the motorcycle and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Be sure to check that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 2. Install the chrome exhaust flanges (supplied) over the front and rear head pipes. 3. Install the rear head pipe to the rear cylinder using the stock 8mm acorn nuts. Route the pipe approximately 3/4″ beneath the swingarm, leaving the nuts finger tight at this time. 4. Install the front head pipe to the cylinder head using the stock 8mm acorn nuts. Its routing follows the stock head pipe, leave the nuts finger tight at this time. 5. Your Vance & Hines mufflers use the stock mounting locations and rubber grommets. Remove the steel spacers and rubber grommets from your stock mufflers and install them into Vance & Hines mufflers in the same locations. 6. Slip a chrome muffler clamp onto the inlet end of each muffler. Install the clamp hardware as shown in figure 1 (hardware supplied). Leave them loose at this time. 7 Slide the left hand muffler assembly (stamped H641) onto the rear head pipe approximately two inches. Mount the mufflers to the motorcycle using the stock bolts, in the stock locations. 8. Repeat the above step with the right hand muffler (stamped H640). 9. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edges of the heat shields with the location of the mounting clips that are welded to the back side of the heat shield. Position the right rear heat shield (stamped H226) over the rear head pipe and feed the tail end of the hose clamps into the clips. Be sure that each clamp is engaged into both clips. Repeat this procedure with each heat shield.

Incoming search terms: