KTM 3V TURBO DRIVE MODEL 9808T KNEE FEED Installation and Removal Manual

0

Filed Under (KTM) by admin on 28-01-2012

download
Gather together the following items that you will need to complete this installation. a) lathe b) 3/8″ electric hand drill c) 9/32″ diameter transfer punch SERVO Turbo Drive Model 9808T Page 2 d) .4375 drill, 3/16″ drill, #7 drill e) 1/4-20 tap f) 3/4″ socket wrench g) set of inch hex wrenches h) clean shop rag Step 2: Clean the power feed mounting area completely. Step 3: Remove the drive clutch nut and the drive clutch from the elevating jack shaft. Step 4: Remove the dial nut, dial, and dial carrier. Keep the dial for reuse later. Step 5: Remove the existing bearing retainer. Keep the screws for reuse later. Step 6: Pull jack shaft out of knee. Hold inboard end up while removing to avoid damage to the pinion gear. Step 7: Press the bearing off the jack shaft. Step 8: Drill and ream the end of the jack shaft .4375″ diameter by 13/16″ deep. The .4375″ dia. must be concentric to the shaft O.D. within .002″ T.I.R. Chamfer 1/32″ x 1/2″ diameter. For best results, machining should be done in a lathe. Step 9: Place the shaft extension #6975 into the end of the jack shaft. Finish drill 3/16″ diameter through the shaft and pin the extension with the 3/16″ diameter x 5/8″ long roll pin. File smooth. Step 10: Reassemble and replace the jack shaft in the machine. Step 11: Replace the existing bearing retainer with #57904 retainer provided. Secure using existing screws. Step 12: Slip spacer #5426 and bearing race #1616 onto the jack shaft. Slide the adaptor #0771 over the bearing race and locate against front of the knee.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL REAR SADDLEBAG GUARDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION 1. Remove saddlebag, if equipped, from motorcycle. 2. Remove passenger footpeg or passenger footboard assembly (including footboard mount) from vehicle. 3. See Figure 1. Remove nut (1), seat strap bracket (if equipped) and 3/8 inch diameter bolt (2) from indicated position on rear fender support (immediately to the rear of the front seat) Discard the bolt, but save the nut for reinstallation. This location is where the upper part of the saddlebag guard will mount. 2 1 is03883 1. Rear fender support nut 2. Rear fender support screw Figure 1. Hardware Removal 4. See Figure 2. Install saddlebag guard (4) top flange (5) against fender support (3). Install 3/8-16 x 1-3/4 inch button head bolt with the seat strap bracket (if equipped) and hardware removed in Step 3 (if equipped) and nut in same direction as bolt removed in Step 3. Finger tighten only. 5. Position bottom flange (6) of saddlebag guard (4) against inboard surface of motorcycle frame (7) at location where passenger footpeg (2) (or passenger footboard bolt) attaches. If Heritage-Style Saddlebag relocation kit, Part Number 90238-00 is to be installed, the bracket should be positioned between the saddlebag guard flange and the motorcycle frame member. Follow installation instructions included with that kit. 6. See Figure 3. Determine your model application and follow the applicable installation procedure below: On models with passenger footpeg, but without saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support (B). Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Install lower saddlebag guard flange over bolt protruding from inboard surface of frame member. Install 3/8-16 lock nut to end of bolt. Tighten to 35-45 ft-lbs (47-61 Nm). Install footpeg (C) according to Service Manual instructions. On models with passenger footpeg and saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support. Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Position saddlebag relocation

Incoming search terms: