Kawasaki ZX6R 2009 Frame Slider Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove mid and lower body panels Left and Right. There is a small plastic cover that is mounted over the main engine stud location on the left side. This cover requires a small notch to be cut out of the cover to clear the small end of the left side offset. Remove stock stud and mount the left side offset (with 10 X 1.25 X 60). Using a pencil, trace out the notch that you need to remove to clear the small end of the offset. We used a Dremel tool with a sanding roll and cleaned it up with an exacto knife. We removed a small amount of material at a time checking for clearance each time. The notch will not be visible after the body has been mounted. See photos below: 2. Once you have notched the small left side panel, mount the left side offset but only hand tight. You need to be able to move the offset by hand to its proper location. 3. Mount the left side bodywork and align the offset to the opening in the body. Mount the left side slider on the offset to ensure correct location. There is a flat notch in the slider so the body will clear. Remove the slider and body and torque down the offset to OEM specifications. (see above)
4. Mount the left side panel. Install the slider using one drop of blue thread locker and torque down to 30 to 32 ft lbs.

2006 – 2007 Harley-Davidson Softail Ultimate seats Installation Manual

0

Filed Under (Harley Davidson) by admin on 04-04-2012

download
1. Remove original seats from your bike. #2. Your new Ultimate seats install using the front seat side mount bolts and the passenger seat is bolted to the front seat and rear fender. Side mount hex nuts = 2. If your stock rider seat is a rear fender mount, install one of the hex nut inserts on each side of the frame if they are not in your bike frame already. #3. All the mounting brackets are already installed on your new seats. #4. Connect our passenger seat to the rider seat with the 2 new round head allen bolts ( 1/4″ x ¾”) #5. Use the 2 new supplied bolts to attach the rider seat to the bike frame, one on each side into the threaded inserts ( 1/4″ x ½”) pan Phillips head) #6. Use the other new bolt for the passenger seat rear bracket in the fender (1/4″ x ½”) pan head. Enjoy the ride again

Incoming search terms:

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

SUZUKI BOULEVARD M109R Fuel Injected Models INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 16-02-2012

download
1. Remove seat, right and left side covers, and fuel tank. 2. Remove airbox. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness as shown in the picture. (Fig 1) 4. Unplug stock wiring harness from injectors and plug in the connectors from Fuelpak as shown. (Fig 2) 5. Unplug the TPS connector (grey) and attach T-tap connectors to the two outside wires. (Fig 3) 6. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown (Fig 3) 7. Reattach the TPS connector. 8. Route red wire to the front of engine and down to the horn. (Fig 4) 9. Disconnect the two position connector from horn and snip connector in half so you have two one-wire connections. 10. Reattach factory grey wire to horn. Attach Fuelpak red wire to the other horn connection. Plug the factory horn orange wire to the male connection on the Fuelpak red wire. 11. Route black wire to battery negative connection as shown. (Fig 5) 12. Attach Fuelpak to Fuelpak harness and mount to bracket under the left side cover as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank.

2007 KTM 250, 450, 505, SX-F QPX Performance Tip/ Spark Arrester Clean out Procedure

0

Filed Under (KTM) by admin on 24-01-2012

download
Step 1: Take off the end cap of exhaust by removing the five (5) screws using a T-20 torx wrench. Cut the silicone around stock end cap using a box knife, then pull cap straight off. Step 2: Step 3: To install your new QPX Performance Tip/Spark Arrester, slide QPX assembly into muffler with engraving on base right side up. Step 4: Align holes of QPX base and muffler, then reinstall the five (5) original screws with your T-20 torx wrench. Installation is now complete. Store instructions in a safe place for future reference. (See clean out instructions on reverse.) If the spark arrester screen isn’t already installed in the QPX Performance Tip, remove the four (4) M6 bolts attaching the cone to the base, remove cone, install screen between base and cone, reinstall M6 bolts and tighten. Do NOT tighten. Start, but leave loose until all screws are started, the tighten securely.

Incoming search terms:

Yamaha YZ250F 2001-2080 Wiseco High Performance Camshaft INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 15-01-2012

download
Wiseco’s new Camshafts are made from premium materials, state-of-the-art forgings, machined to exact tolerances, and specifically engineered for high performance and maximum durability. Brought to you by one of the most trusted names in the industry… Wiseco. Wiseco Cam- blue OEM Cam- red Wiseco’s new high-performance camshafts for the Yamaha YZ250F produce 3% horsepower and 3% torque gain over the stock OEM camshaft across the entire RPM range.

Incoming search terms:

YAMAHA SINGLE SIDED SWINGARM REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 27-12-2011

download
1. Disconnect Battery 2. Lift and secure bike 3. Remove brake-side floorboard 4. Remove exhaust. 5. Remove rear fender 6. Remove front pulley cover 7. Remove wheel, pulley, and brake assembly simultaneously. Now remove front pulley from transmission. (Keep up with the stock nut and lock washer; these will be used during assembly) 8. Remove Passenger pegs; now remove the plastic covers in the frame that cover the pivot tube bolts. 9. Remove the stock shock bolts ( keep for re-assembly) 10. Remove the pivot tube bolts. 11. Remove the stock swingarmb12. Install “new” belt at this time. 13. Install supplied pivot tube, and bearings in RC swingarm. 14. Install shock bolt with red loctite in RC swingarm. (Do not tighten bolt at this time) 15. Insert supplied pivot bolts with red loctite through frame and supplied bushings into the RC swingarm. (Right side bushing has flats) 16. Torque shock and pivot bolts to factory specs. 17. Install belt adjustment bolts and single side keys into swingarm.

Incoming search terms:

2006-2007 Honda TRX450R SR4 4 Stroke racing system INSTALLATION

0

Filed Under (Honda) by admin on 30-11-2011

download
Install Motoworks header pipe using stock nuts, finger tight at this point ( Fig 4) 2. Install Motoworks tailpipe with muffler using bolt and spacer supplied in kit on upper rear mount, use stock nut and bolt on lower mount finger tight at this point. (Fig 5 and 6) 3. Torque header pipe nuts to 1.0 kg-m ( 7.3 lb-ft ) 4. Torque tailpipe mounting bolts to 2.5 kg-m ( 18 lb-ft ) 5. Re-check all your work 6. We recommend that you clean the entire exhaust system with a mild detergent, i.e. glass cleaner prior to starting as any oily residue may cause permanent stainingBefore operating check for proper clearance between Motoworks exhaust and ATV i.e. frame, plastic, brake line, fuel line etc if problems exist re-check work

Honda RC51 2000-2005 SBK Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 22-11-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Your subframe may be different but the cutting position is the same on all years. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary Replace all bodywork with fasteners loosely installed, mount undertail,
notice at bottom of the tray there are 2 holes, mark and remove tray, then drill holes in battery box 6) Inset lock into undertail using stock lock mounting clip, make sure the lock is in the correct position with the lock cable arm to function
properly. Insert undertail left side first, then right side, be carefull not to crack or scratch undertail. Use your stock plastic screw rivets to hold undertail in place. Attach lock cable to lock, check movement, adjust if necessary. Tighten all hardware on tail section, attach seat. * After this modification your undertail is not returnable. Paint is not war-
rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.
6) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

HONDA VTX1800R & HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 10-11-2011

download
harness. Remove wire tie (take note of harness routing for reassembly). Un-route wires and drape over right side of pipe. 3. Remove entire right side floorboard assembly, (three bolts) (Figure 1). 4. Remove exhaust port flange nuts.
5. Remove flange bolts securing rear muffler mount to exhaust system mounting bar. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). 7. Remove rectifier from mounting bar. 8. Remove stock (cast iron) exhaust system mounting bar.