2000-2003 MXC / EXC Dual Sport Kit Installation Manual

0

Filed Under (KTM) by admin on 05-02-2012

download
1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side anels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees

KTM ELECTRICAL SYSTEMS INSTALLATION, REPAIR

0

Filed Under (KTM) by admin on 02-02-2012

download
DC SYSTEMS STEP DC1 – REGULATOR/RECTIFIER: PRE-2005 KTM If the stock regulator looks like below (the stock connector will not plug into the Trail Tech regulator/rectifier) then the provided stub connector must be soldered into the bike’s wire harness. For models without a stock battery, mount the reg/rec and plug the stub connector into it. Run the red and black wires directly to the (aftermarket) battery, and the yellow wires to the stator. SEE DC CIRCUIT DIAGRAM ON REVERSE SIDE OF PAGE. MODELS WITHOUT A STOCK BATTERY Move stock light to the DC circuit: divert lighting wire from AC circuit to DC circuit. In stock form, the lights are powered by the AC half of the electrical system. In order to continue to use the stock light, find the yellow wire (runs to stock headlight) shown below (wire bundles are found underneath gas tank) and cut the smaller gauge yellow wire. 1. Connect aftermarket light: Wire the light’s red(+) light lead to the positive(+) battery terminal, and the black(-) light lead to the negative(-) battery terminal. Trail Tech lights should use a 10-20 amp fuse as close to the positive(+) battery terminal as possible.

2000-2003 KTM MXC / EXC Dual Sport Kit Installation Manual

0

Filed Under (KTM) by admin on 01-02-2012

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3 4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

TOYOTA ALL MODELS BATTERY MAINTENANCE FOR IN-STOCK VEHICLES

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
A battery in a stored vehicle is subject to conditions which can reduce its performance and life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are recommended in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for excessively discharged and/or failed batteries due to
lack of maintenance. It is considered the dealers responsibility to maintain the specified state of charge of the vehicle’s battery while in stock. BATTERY MAINTENANCE RECOMMENDATIONS: 1. A monthly battery inspection is recommended under normal conditions. If your dealership is located in an area subject to extreme temperatures (hot or cold), periodic maintenance may need to be performed on a more frequent basis. When maintenance requires removal of filler plugs on vehicles with “maintenance free” batteries, new labels are available via the following part numbers: