Ducati ST2/ ST4 Left Side Installation and Removal Instructions

0

Filed Under (Ducati) by admin on 28-04-2012

download
STEP #1 Remove necessary fairings. STEP #2 Mount the bracket-utilizing factory holes located under the passenger rear set. STEP #3 Route wires starting at the bracket end and finishing at the battery. STEP #4 Look over your work. STEP #5 Check the polarity & test. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 – Remove the seat, front, right side, & left side tail fairings. See the Ducati service manual. STEP #2 – (RIGHT side shown, perform on LEFT) If your bike was equipped with a stock outlet unplug the existing harness & tie wrap this up out of the way, it is not used. Also remove the stock bracket from behind the rearset. Attach the new bracket behind the frame utilizing the two holes below the passenger rear set. Install the supplied 6mm hardware into the front hole and just snug them up. Adjust the bracket so rear hole is aligned with the hole in the frame; the tail fairing bolt & spacer go back in this hole later. Tighten the supplied front screw to 6 Nm.

HONDA GL1800 DRIVER BOARD SETS WITH HEEL TOE SHIFTER INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Note: Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Remove the two bolts that hold the stock left side foot peg bracket and remove bracket and foot peg. 2.2. 2 3. Install shifter slot over shifter peg. 4. With the longer bolts supplied, sandwich the Heel Toe Shifter plate between the frame and chrome bracket provided. 4. 5. Screw in bolts and secure tightly. Double check the tightness per service manual. 6. Replace stock peg with the driver board provided. 7. Install driver board with hardware provided. 8. Right side. Remove stock bracket and peg. Replace with chrome bracket and floorboard with stock bolts.

BUELL XB9R REMOVABLE SADDLEBAG KIT Installation Instructions

0

Filed Under (Buell) by admin on 03-02-2011

download
Installation 1. Ensure that the tail section of the motorcycle is clean and dirt free. 2. See the Service Parts illustration. Using a T27 TORX drive head, remove the two screws holding the tail section underside shield. 3. Install the saddlebag bracket (3) as shown, reinstall the screws and tighten securely. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. The mounted saddlebags will cover the factory-installed rear side reflectors on these vehicles. Reposition, or have a dealer reposition, the original rear side reflectors supplied with this motorcycle or apply new ones. If this is not done, the loss of visibility to other motorists may result in death or serious injury. NOTE New reflectors (Part number 59256-84A) are available from your Buell Dealer. NOTE When removing adhesive residue, take care to keep from scratching or damaging the reflector, mounting bracket or surrounding parts. 4. Use a thin flat blade, like that on an X-Acto knife, and carefully pry the reflectors off of their mounting brackets. Remove the adhesive residue from the brackets and the back of the reflector. 5. Mount the new reflector relocation brackets (4) to the stock reflector mounting brackets as shown. Attach each relocation bracket through the slots in the stock bracket with two screws, flat washers and lock nuts from the Hardware Kit (5). Slide the relocation bracket to the rearmost position and tighten securely. 6. Remove the outer release liner of the foam tape on the relocation bracket. Mount the stock reflector squarely to the bracket, and press firmly in place. 7. Remove the passenger pillion (and pillion cover, if mounted), and set aside. 8. Position one of the saddlebags to the side of the motorcycle tail section with the Buell logo facing out, and to the rear. Hook the mounting pocket on the back side of the bag onto the saddlebag bracket mounted earlier. Repeat for the other saddlebag. 9. Bring the saddlebag straps up and over the tail sectiion. Pull the right-side straps up through the buckle eyes on the left-side straps, remove any slack and fasten the hook-and-loop material. 10. Note the points where the saddlebags and straps contact the motorcycle tail section. Two lengths of clear protective tape have been provided in the Hardware Kit. If desired, cut and fit lengths of the tape to those areas of the tail section to prevent damaging the finish. 11. Replace the passenger pillion (and pillion cover if desired). Position the front tongue on the pillion overthe saddlebag straps

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

Incoming search terms: