YAMAHA YFM 350 Removing stock carburetor and cables.

0

Filed Under (Yamaha) by admin on 19-01-2012

download
Remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Preparing motor for carburetor install 1. Remove stock manifold from cylinder head. 2. Place supplied o’ring into aluminum flange as pictured in figure 1. Figure 1. 3. Install aluminum and rubber flange to motor using supplied bolts. See Figure 2. The shorter 25mm bolt will need to be placed in the bottom hole. IMPORTANT NOTE: Install the aluminum flange with the o’ring towards the motor and the thick side up.

Incoming search terms:

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

1996-2004 HONDA XR250R Removing stock carburetor and cables

0

Filed Under (Honda) by admin on 26-11-2011

download
Install the throttle cables into the supplied throttle housing and place onto clean handlebar end. 2. Remove the rubber carburetor alignment tabs from the manifold using a razor blade or sharp cutters. This should be done with the rag left in the manifold. Be very careful not to damage the manifold or your hands while doing this!! 3. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering
adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 4. Install provided fuel line onto fuel inlet banjo and secure with pinch clamp. 5. Place Edelbrock carburetor into manifold. Do not tighten clamp yet. 6. Remove the cable bracket end from cable bracket using #2 phillips. 7. Install pull cable (see Figure 2) end into
the 4:00 position of the cable wheel and the return cable into the 1:00 position. Secure cables into cable bracket by replacing end piece and phillips screw. See figure 3.

Incoming search terms:

Harley-Davidson Carburetors TUNING INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
CARBURETOR REMOVAL Edelbrock recommends consulting an authorized service manual for make, model and year of motorcycle before disassembly of stock parts. 1. Turn fuel valve off before getting started. 2. Disconnect battery to eliminate the possibility of sparks or accidentally engaging the starter. 3. Remove air cleaner assembly. 4. Disconnect choke cable from its bracket. 5. Disconnect fuel line and vacuum lines from carburetor. 6. Gently remove carburetor from manifold. NOTE: For removal of CV style carbs, Edelbrock recommends the carb be gently wiggled from side to side (not up and down) while pulling to get carb out of manifold. MANIFOLD REQUIREMENTS Edelbrock Quick Kits and Complete kits are designed to work with the stock manifold that was OE on your engine. Some aftermarket manifolds will also work with Edelbrock carburetors. S&S “E” Series and Screamin’ Eagle flange mount manifolds will work with Edelbrock flange style carburetors. It is also recommended the manifold being used closely matches the venturi of the carburetor. BIKE PREPARATION 1. Once stock carburetor and air cleaner have been removed, inspect manifold grommet (CV manifolds only) for tears, nicks or cuts. Replace grommet, if damaged. Stuff a clean dry rag into manifold until carb is installed to keep any debris out of engine. 2. Remove old fuel line and vacuum line (if equipped) and install supplied fuel line and vacuum line

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

Incoming search terms: