Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

Incoming search terms:

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

Incoming search terms:

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

HONDA VTX 1300 Retro BIG SHOTS EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 07-12-2011

download
Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install and tighten supplied mounting bracket (stamped
346-P) in the original mounting bar location, using two M10x40 flange bolts, nuts, and washers (supplied) (Figure 1). 3. Install and tighten rectifier using M6x30 flange bolt, nut, and washer combinations (supplied)(Figure 1). 4. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker, mark the outside surface of front and rear heat shields with the location of the mounting clips welded inside(Figure 2). 5. Install each heat shield over its respective head pipe (Figure 3). 6. Install each hose clamp by feeding tail end of clamp into heat shield clip. Take note of clamp screw head direction (Figure 2 & 4). Screw head should be ccessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas. Note: Prior to tightening hose clamps, align end caps so that slash ends are even.

HONDA 2005 CRF 50 F AKRAPOVIC RACING EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 03-12-2011

download
put the motorcycle on a side standn 2. unscrew and remove the bolts from the rear and front part of the motorcycle cowling (Figure 1, 2, 3, 4) m3. remove complete cowling together with the seat (Figure 5) 4. unscrew the bolt from the metal bracket for the muffler (Figure 6) 5. unscrew and remove the bolts on the flange of the header tube (Figure 7) 6. remove the stock exhaust system (Figure 8) 7. remove the stock heat shield (Figure 9) INSTALLATION OF THE AKRAPOVIC RACING EXHAUST SYSTEM installing the header tube: 1. attach the stock heat shield onto the Akrapovic header tube (Figure 10, 11) 2. set up the Akrapovic header tube and hand tighten the flange; use stock gasket; (Figure 12, 13) 3. make sure the header tube is not touching the engine or frame installing the muffler:
1. correctly position the muffler and slide it onto the header tube (Figure 14) 2. attach the spring at the muffler – header tube joint igure 15) 3. attach the muffler to the chassis hanging bracket – use the bolt, washer and spacers supplied in the Akrapovic kit. Do not
fully tighten. Make sure the additional parts from the Akrapovic kit are correctly installed. (Figure 16, 17) 4. make sure the header tube is not touching the engine or frame final installation: 1. tighten fully the bolts of the muffler metal bracket and header tube flange (Figure 18, 19) 2. reattach the complete cowling (Figure 20, 21, 22, 23, 24) 3. clean grease spots: a. muffler – titanium outer sleeve: use a soft cloth sprayed with a multi-purpose spray lubricant (WD-40 or equivalent) b. stainless steel header tube: use a soft cloth sprayed with a contact cleaner, then wipe with a soft dry cloth Cleaning will prevent spots from burning onto the surface. Do not use aggressive chemical cleaners, because they can damage the sticker. 4. position of the correctly installed Akrapovic RACING system (Figure 25)
5. Check the operation of the brakes and suspension. Make sure all the bolts are sufficiently tightened. In case the exhaust system touches the cowling or other parts repeat the adjustment of the exhaust system or contact your authorized dealer

Honda RC-51 / VTR-1000 SP1 – Installation Instructions

0

Filed Under (Honda) by admin on 23-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the mid pipes rearward. Save the exhaust clamps for reuse Save the stock exhaust can mounting bolts and nut for the end can to the passenger footpegs for reuse as well. Inspect the original exhaust gaskets. Replace as necessary. Slide the tail pipes into place. Do not tighten the clamps at this point. Slide the TiForce end cans into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to each end can using the supplied 6mm hardware H. See figure 1 for details. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G
(see figure 1). Attach the supplied springs to all the joints (from the tail pipes to the TiForce end cans). Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can, then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO
BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN(s).

Honda CBR-600 F4 / F4i – Installation Instructions (slip-on)

0

Filed Under (Honda) by admin on 11-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the middle of the stock pipe. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Remove the clamp from the stock exhaust system and save for reuse. Install the S-Bend to the rear of the stock head pipe. Reuse the stock clamp, but do not tighten at this time. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 190-200mm from the edge of the end can. See figure 2 for details.
Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
Attach the supplied springs to fasten the end can to the S-bend pipe. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced prope rly on the can (refer to step 7 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system

Honda CBR-1100xx Blackbird – Installation and Removal Instructions

0

Filed Under (Honda) by admin on 03-11-2011

download
Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the
radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and
pivot the oil cooler forward to provide access.
2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting
bolt and nut for the end can to the passenger footpeg for reuse as well.
3. Inspect the exhaust gaskets. Replace if necessary.
4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to
the pair of front Y-pipes. Do not install the exhaust springs at this time.
5. Remove the rubber center stand stop from the stock exhaust system. Insert the rubber stop into the supplied
steel bracket. Mount the bracket to the right side of centerstand using the stock mounting bolt, and tighten fully.
6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing
for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the
ends of the headpipes fit flush and snug in the ports before tightening.
7. Install the S-Bend to the front section of the headpipes and two Y-pipes.
8. Go back and retighten the head pipe flange nuts per factory specification.
9. Slide the TiForce end can into place.
10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the
supplied 6mm hardware H. See figure 1.
11. Place the bands approximately 115mm from the edge of the end can. See figure 2.
12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. Please

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

Incoming search terms: