DYNA IGNITION COIL INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 08-11-2011

download
Remove the gas tank. Locate the two ignition coils. 2) Unplug the primary wires coming from the coils and disconnect the high voltage wires from the spark plugs. Remove the coil mounting bolts, and remove the coils. 3) Cut or unsolder primary wires from coils. Crimp or solder ring terminals supplied with kit to primary wires.4) Attach the primary wires to the DYNA COILS using the 10-32 x 5/16 pan head screws provided. Either wire can be mounted on either terminal of the dual output coils as they have no polarity. On the single output coils, the primary terminal opposite the side with the output tower has a + marking. Plus 12 volts from the ignition switch is applied to that terminal, and the points or ignition system output is connected to the other terminal. On a Kawasaki, make sure there is clearance between the screw head and the mounting screw spacer. Do not over- tighten screws as damage to the coil could result. 5) Using the stock hardware, mount the coils to the frame in the original location. NOTE: The DYNA COIL mounting hole spacing is designed to accommodate early model Honda, Kawasaki, and Suzuki motorcycles. There are a wide variety of physical sizes and mounting configurations on the late model motorcycles and it may e necessary to modify existing mounting brackets, or fabricate a bracket to adapt the DYNA COILS to your particular motorcycle

HARLEY DAVIDSON FENDER SUPPORT COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL NOTE Complete all removal and installation procedures on one side before performing on the other side. 1. See Figure 1. Remove rear turn signal assembly (2) following the instructions in the service manual. Save all hardware for installation. 2. Remove the upper shock absorber hardware (3) following the instructions in the service manual. Save all hardware for installation. 3. Remove the rear fender support cover (4) following the instructions in the service manual. Save all hardware for installation. INSTALLATION 1. See Figure 1. Install the rear fender support cover (4) with the stock hardware. Tighten finger-tight. 2. Install the rear turn signal assembly (2) following the instructions in the service manual. 3. Install the upper shock absorber hardware (3) following the instructions in the service manual. 4. Remove the rear fender support cover hardware and apply Loctite Threadlocker and Sealant 243 (Blue) to the threads of the screws. Tighten screws to the specifications in the service manual. 5. Thoroughly clean the mounting surface of the fender support cover with an equal mixture of water and isopropyl alcohol. Peel the paper backing from the new reflector and install reflector (1). Press the reflector firmly. Allow AT LEAST 24 hours after applying the reflectors before exposing the areas to vigorous washing, strong water spray or extreme weather

HARLEY DAVIDSON DYNA GLIDE CUSTOM SEAT KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat from motorcycle. Keep lockwasher and screw. 2. Remove existing grab strap and all attaching hardware. 3. Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). 4. On all models, except FXDWG , install existing stock rear bracket onto seat using stock hardware. On FXDWG models, install the new rear bracket, 52152- 97 onto the seat using the stock hardware. 5. Position new seat on motorcycle. Be sure bracket on front of seat fully engages seat mounting tab on frame. NOTE On rear fenders of 1997 -2003 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997 – 2003 models. 1996 DYNA MODELS ONLY Secure seat with stock screw, stock lockwasher and place stock nylon washer between seat bracket and fender. 1997 – 2003 DYNA MODELS Secure seat with stock screw and stock lockwasher.

HONDA VT750 EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 24-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the header flange nuts at the exhaust port on the front and rear head pipes. 2. Remove the two 8mm nuts from the muffler mounting bracket, while supporting the entire exhaust system. Lower the system down and set it aside. Note: Save the stock hardware for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install the muffler mounting bracket (stamped 268) to the original muffler mounting point, using the two stock 8mm nuts. Refer to figure 1. 3. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the front muffler. 4. Install the front head pipe to the cylinder head using the stock nuts. Attach the muffler to the mounting bracket using the two 5/16″ flange bolts (supplied). Leave the nuts and bolts loose at this time. 5. Repeat steps 2 and 3 with the rear header. 6. Align the mufflers so they are parallel when viewing from the right hand side of the motorcycle. Tighten all the hardware evenly. 7. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. 8. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Note : The heat shields should cover the weld on the muffler. 9. Be sure to remove any dirt, oil or finger prints from the entire exhaust system before starting the motorcycle.

HONDA VF750 MAGNA SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the left and right side frame covers to prevent damaging them. 2. Loosen the pinch clamps on the inlet end of all four mufflers, located behind the rear motor mount. 3. Remove the left and right front head pipes. 4. Remove the rear mounting bolt from both muffler assemblies. Carefully slide each muffler assembly off the head pipes and set them aside. 5. Replace the front head pipes. Note : Leave the head pipes loose for later adjustment. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 2. Place the slip-on head tube into the matching heat shield, wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head tube. Repeat this step with opposite head tube and heat shield. 3. Slide a T-bolt band clamp (supplied) onto the slotted end of each slip-on tube. 4. Slip the slotted end of tube onto the rear head pipes. The shorter of the two slip-on tubes mounts on the right rear head pipe and the longer tube on the left rear head pipe. Tighten the T- bolt clamp until the pipe is snug but so the pipe will still be able to rotate. 5. Install the muffler mounting brackets to the frame using the single hole in the brackets and the stock hardware. The left side mounting bracket (stamped #206 on the bracket) mounts to the outside of the frame, where the stock muffler assembly mounted. The right side bracket (stamped #207) mounts to the inside of the frame, behind the stock muffler mounting point. 6. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (all supplied). Do this to each muffler but leave the clamp loose at this time. 7. To determine the difference between the left, right, upper and lower mufflers refer to the number stamped on the bracket welded to the backside of each muffler. The top right hand muffler is D500, the bottom right hand muffler is D510, the top left hand muffler is D550 and the bottom left hand muffler is D512. Note : The endcap bolts should face down and inward when viewing from the rear (Refer to Figure 1) .

YAMAHA V-STAR 650 EXHAUST SYSTEM REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the right hand frame cover to avoid scratching it. 2. Remove the nuts that mount the rear header to the cylinder head. 3. Loosen the pinch clamp on the inlet end of the lower muffler. 4. Remove the two bolts that mount the mufflers to the muffler bracket, located between the two mufflers. Save the hardware for reuse. 5. Pull the rear head pipe out of the exhaust port. Slide the muffler assembly with the rear head pipe attached, rearward, disconnecting it from the front head pipe. Set the assembly aside. Note: Keep the front head pipe attached to the motorcycle, it will integrated with the new exhaust system. 6. Remove the muffler mounting bracket from the frame and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the V&H muffler mounting bracket (stamped 272) to the frame using the stock hardware and mounting location. Refer to figure 1 2. Slip the T-bolt band clamp (supplied) over the straight pipe that is welded to the front muffler. 3. Slip the front muffler assembly over the stock head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 4. Install the rear header assembly to the exhaust port using the stock 8mm nuts, but leave them loose at this time. 5. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the rear muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 7. Align the mufflers so they are parallel when viewing from the right side of the bike, and tighten the 5/16″ flange bolts on the back side of both mufflers. 8. Tighten the two header flange nuts on the rear head pipe. 9. Tighten the T-bolt clamp at the slip joint of the front muffler. 10. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. Note: The edge of the heat shield should just cover the weld on the inlet of each muffler, if not, adjust the heat shield for correct alignment

Honda VTX1800C/ J Left/ Ringht Floor Board Assembly Instruction Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Left Side 1. Unplug the horn wires. 2. Unbolt the left side foot peg bracket assembly and save the hardware, the stock bolts will be used to install your new Cobra floorboards. 3. Remove horn and the shift lever from the stock mount and install onto the new Cobra mount the same way they were on the stock mounts. Install the 8mm acorn nut on the exposed threads from the shift lever bolt. 4. Bolt the Cobra floorboards to the motorcycle using the stock bolts and torque to factory specifications. Note: Make sure shift lever operates properly and that there is adequate clearance. Right Side 1. Remove chrome cover from the top of the rear brake master cylinder by removing the two nuts on top. 2. Remove brake lever return spring and the stop light switch spring. 3. Remove rubber plug from the center of the brake lever pivot bolt then remove the bolt. 4. Remove the two bolts that hold the master cylinder and brake light switch/chrome cover mount. 5. Unbolt the right side foot peg bracket by removing the two stock 10mm bolts and save the hardware, the stock bolts will be used to install your new Cobra floorboards. Note: look at the placement of the large spacers behind the foot peg bracket they will need to be re-installed in the same position. Also note the nut on the inside of frame rail for lower bolt. 6. Install the Cobra floorboard using the stock bolts and spacers removed in previous step. 7. Remount the master cylinder and brake light switch/chrome cover mount removed in step 4 the same way it was on the stock mount bracket, reuse stock hardware. 8. Install the brake lever using the stock pivot bolt & rubber plug that was removed in step 3

Kawasaki ZRX1100/ 1200 Competition Meg Series Exhaust INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL IMPORTANT: This product will greatly improve the flow of your exhaust system. RE-JETTING WILLBEREQUIRED after installation. Please consult your local dealer or a certified techhnicial for appropriate recommendations. You will also need to replace the stock headpipe to cylinder gaskets. These are available at your Kawasaki dealer. 1 Using a 1/4 drive 12mm socket with a 12″ extension and swivel, remove the nuts and split flanges holding the headpipe to the ports. (Retain the nuts and split flanges for installation.) 2 Remove the acorn nut holding the stock muffler in place. (Retain for installation.) 3 Remove the two allen head bolts holding the foot peg bracket and remove the bracket. (Retain for installation.) 4 Remove mid-mount bolt holding the headpipe at the rear of the engine and remove system 3 Install collector assembly onto head pipes. Align all (4) headpipes with the appropriate port on the collector (see figure #1). Using a rubber mallet, tap each pipe into the collector. DO NOT hammer the headpipes all the way into the collector, always make sure that the outlet end of the collector assembly is positioned away from the swing arm and engine sump. 4 Slip the muffler over the outlet of the collector assembly. Align the mount bracket so it is pointing upward (the muffler bracket will be on the inside of the foot peg bracket). 5 Slide the stock muffler mount bolt through the mount hole in the muffler and re-install the stock foot peg bracket using the stock hardware. 6 Re-install the stock acorn nut to the muffler mount bolt and tighten. 7 Align all system components and finish seating the primary headpipes into the collector assembly. 8 Tighten each head pipe at the exhaust port. 9 Install (4) springs, supplied in the hardware kit, from the collector to each headpipe and (2) springs from the muffler to the collector assembly. *IMPORTANT: AFTER A SHORT RIDE CHECK AND RETIGHTEN ALL FASTENERS.