HARLEY DAVIDSON ADJURE'S BIG CITY LED LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 20-04-2012

download
ADJURE OFFERS DOT COMPLIANT LED REPLACEMENT TURN SIGNALS TO FIT BOTH THE FLAT AND FOOTBALL HARLEY DAVIDSON TURN SIGNAL HOUSINGS. STOCK HARLEY DAVIDSON HAS 3-WIRE AMBER (RUN/TURN) IN FRONT AND 2-WIRE AMBER (TURN ONLY) IN THE REAR. IF YOU WANT TO CHANGE YOUR REAR TURN SIGNALS INTO RUN/TURN/BRAKE, YOU MUST CHANGE THE LENS COLOR TO RED AND THE BEST WAY TO DO THIS IS TO ALSO ORDER AND INSTALL OUR P/N# K48590 (RUN/TURN/BRAKE CONTROLLER). NOTE: WHEN USING LED’S AS A TURN SIGNAL YOU MUST ALLWAYS USE A “LOAD EQUALIZER” P/N#K48100 TO MAKE THEM WORK PROPERLY. INSTALLATION: COVERS BOTH FLAT AND FOOTBALL HOUSINGS 1) REMOVE THE LENSES FROM YOUR STOCK TURN SIGNALS BY REMOVING THE 2 SCREWS ON EACH SIDE OF THE LENS. 2) REMOVE THE BULB BY PUSHING IN AND TURNING COUNTER CLOCKWISE. 3) INSERT INTO THE LIGHT SOCKET THE PLUG ON YOU NEW LED’S BY PUSHING IT IN AND TURNING IT CLOCKWISE. 4) SET THE LENS ON THE HOUSING AND REPLACE THE SCREWS. TO CONNECT THE LOAD EQUALIZER: 1) THERE ARE 3 WIRES CONNECT THE BLACK TO A GOOD GROUND AND ONE OF THE WIRES TO ANYWHERE IN THE LEFT SIDE TURN SIGNAL SYSTEM AND THE OTHER WIRE TO ANYWHERE IN THE RIGHT SIDE TURN SIGNAL SYSTEM.

2006 Harley Davidson VROD / Screamin' Eagle VROD Installation Manual

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Check top clamp holding on rear heat shield be sure this is mounted forward not in middle of pipe. 2. Slide rear head pipe into collector and leave loose. 3. Mount head pipes into exhaust ports using stock Harley gaskets hand thread nuts onto head studs, leaving play in pipes. 4. Slip muffler onto collector and leave loose. 5. Slide D&D bracket included with kit onto chassis and muffler together. 6. Hand thread nuts onto chassis studs 7. Align muffler flush with bracket, hand thread bolts onto muffler.
8. Push system together tightly, Tighten rear head pipe collector clamp. 9. Holding muffler into place (finger width between shock bolt) tighten down muffler clamp all the way. 10. Snug (do not torque) chassis bracket bolts, snug muffler bolts until all is correctly aligned, then tighten down bolts. 11. Tighten head bolts down using factory torque specs, as you tighten the pipe check muffler clearance. If to close to swing arm push in on head pipe. If to far away push in on head pipe. 12. Once all is tight start bike and check for leaks This system is designed to be used with a high flow air filter and D&D VRDSEDD2.MT4 Race Tuner map.

HARLEY DAVIDSON TOURING PILLION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION 1. Remove stock pillion from motorcycle according to applicable Service Manual instructions. 2. For FLSTN models: Remove the rear mounting bracket from the stock pillion, and save all the hardware. For all other models: Skip to Step 4. 3. See Figure 1. Install the rear mounting bracket (D) removed in Step 2 onto the touring pillion using the stock mounting screws (C). Tighten screws to 19 in-lbs (2.1 Nm) . 4. Install touring pillion (1) to double mounting studs (A) behind seat (B) by sliding the two slots in the pillion base into the grooves on the double mounting studs. 5. For kit 52930-05: Use the stock screw to fasten the rear seat bracket to the fender. For all other kits: Fasten the rear seat bracket to the fender using screw (6) in kit. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. Install grabstrap (2) using screws (3), washers (4) and spacers (5). SERVICE PARTS A 6 D C B 1 4 2 3 5 is00221 Figure 1. Service Parts: Touring Pillion Kit Table 1. Service Parts: Touring Pillion Kit Part Numbers Description (Qty) Item Not sold separately Touring pillion 1 51186-89B Grab strap 2 4180 Screw (2) 3 6379W Washer (2) 4 6019 Spacer (2) 5 2952A Rear mounting screw (2) (Not needed for Kit 52930-05) 6 Items in text not in kit: Double mounting stud (2) (stock) A Seat (stock) B Rear seat bracket screws (2) (FLSTN only) C Rear seat bracket (stock)

Incoming search terms: