Suzuki M- 109 Front Head Pipe Installation Manuals

0

Filed Under (Suzuki) by admin on 18-02-2012

download
1. Remove seat (Fig 1) remove right side (Fig 2) panel with allen 6mm bolt and push-pin snap. (Fig 3) Figure 1 Figure 2 Figure 3
- 3 – 2. Remove 6mm bolt on heat shield and remove heat shield. (Fig 4) Figure 4 3. Remove two 8mm bolts on top muffler and remove two 8mm stock bolts on bottom muffler and remove mufflers. (Fig.5 & 6) Figure 5 Figure 6 4. Remove frame cover with stock allen 6mm bolt. (Fig 7) Figure 7 FFF – 4 – 5. Loosen brake pedal bolts to allow more room to remove the exhaust. (Fig 8) Figure 8 6. Remove exhaust system by removing stock 8mm bolts on exhaust flanges. (Fig 9) Figure 9 7. Unplug EXCVA wire connectors. (Fig 10) Figure 10 – 5 – 8. Remove three 8mm stock mufflers mounting brackets bolts as shown. (Fig 11) Figure 11 ffff 9. Remove EXCVA unit from the stock muffler bracket. (Fig 12) Figure 12 10. Remove the stock pulley from the EXCVA actuator unit as shown. (Fig 13)

Incoming search terms:

Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

2008-2009 HONDA CBR 1000 RR DUAL CANISTER SLIP-ON INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-11-2011

download
INSURE THE EXHAUST SYSTEM AND EXHAUST COMPONENTS ARE FULLY COOLED. 2. INSURE THE MOTORCYCLE IS STABLE ON KICKSTAND OR REAR CENTERSTAND OR SERVICE TABLE. 3. REMOVE THE 3 PLASTIC BUTTONS HOLDING THE PLASTIC COVER OVER THE EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET) DETACH THE CABLE END FROM THE SERVOnWHEEL AND REMOVE THE ENTIRE CABLE FROM THE RETAINING CLIP. THE ENTIREnCABLE WILL NOW REMOVE WITH THE REST OF THE EXHAUST.REPLACE THE PLASTIC COVER FOR THE SERVO AND REINSTALL THE 3 PLASTIC BUTTONS. 6. REMOVE THE STOCK MUFFLER MOUNTING BOLT. REMOVE 7. REMOVE THE STOCK EXHAUST CLAMP. (IT IS NOT UNCOMMON FOR THE CLAMP BOLT TO BREAK DURING REMOVAL.)b8. REMOVE THE ENTIRE STOCK EXHAUST ASSEMBLY. BE CAREFUL NOT TO SCRATCH THE SWING ARM DURING REMOVAL. 9. REMOVE THE STOCK EXHAUST GASKET FROM HEADER PIPE IF IT DID NOT COME OFF WITH THE STOCK EXHAUST. THIS GASKET WILL
NOT BE USED. 10. PREASSEMBLE THE HYPERFLO EXHAUST BEFORE INSTALLING. HYPERFLO RECOMMENDS YOU DO THIS PORTION ON CARPET OR A CLEAN PADDED AREA. YOU MAY ALSO USE THE PLASTIC BUBBLE PACKAGING AS A PAD TO PROTECT THE CANISTERS DURING PREASSEMBLY. 11. PREASSEMBLE THE LARGE DIAMETER CAN TO THE S-PIPE FIRST. INSTALL THE SPRING ON THE CANISTER FIRST AND PULL AWAY FROM THE CANISTER TO INSURE YOU DO NOT SCRATCH THE CANISTER

HARLEY DAVIDSON DYNA STREET PERFORMANCE SLIP-ON ACCESSORY MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meets all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

HARLEY DAVIDSON DYNA SLIP-ON ACCESSORY MUFFLERS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. -J04263 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

KAWASAKI VULCAN 800 STRAIGHT SHOT EXHAUST SYSTEM INSTALATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header flange nuts from the front and rear head pipes. 2. Remove the acorn nut located under the rear muffler. 3. Remove the two allen bolts located under the front muffler. 4. Remove the stock exhaust system from the motorcycle and set it aside. 5. Remove the two hex head bolts that attach the stock muffler mounting bracket to the frame of the motorcycle. Remove the muffler bracket and set it aside. 6. Remove the two rubber grommets and spacers from the stock muffler and the one grommet and spacer from the muffler mounting bracket. Set them aside with the the two mounting bolts, they will be reused during installation. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install a chrome header flange onto the front and rear head pipes. 3. Install the heat shield to the front head pipe using the two hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe with the heat shield attached, to the front cylinder using the stock nuts. Leave them loose at this time. 5. Install the rear head pipe, with the heat shield attached, to the rear cylinder using the stock nuts. Leave them loose at this time. 6. Install the stock rubbber grommets and spacers into the three large holes on the V&H mounting bar (See figure 1). 7. Slide one dog bone shaped nut plate under the bracket that is welded to each muffler. 8. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Do this to each muffler but leave the clamp loose at this time. 9. Install one muffler to the four hole bracket welded to the V&H mounting bar using the two 5/16″ flange bolts (supplied) and leave them loose. (See figure 1) 10. Slip the muffler and mounting bar assembly onto the front head pipe while aligning the grommet holes in the mounting bar with the holes in the frame.

Incoming search terms:

HONDA VF750 MAGNA SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the left and right side frame covers to prevent damaging them. 2. Loosen the pinch clamps on the inlet end of all four mufflers, located behind the rear motor mount. 3. Remove the left and right front head pipes. 4. Remove the rear mounting bolt from both muffler assemblies. Carefully slide each muffler assembly off the head pipes and set them aside. 5. Replace the front head pipes. Note : Leave the head pipes loose for later adjustment. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 2. Place the slip-on head tube into the matching heat shield, wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head tube. Repeat this step with opposite head tube and heat shield. 3. Slide a T-bolt band clamp (supplied) onto the slotted end of each slip-on tube. 4. Slip the slotted end of tube onto the rear head pipes. The shorter of the two slip-on tubes mounts on the right rear head pipe and the longer tube on the left rear head pipe. Tighten the T- bolt clamp until the pipe is snug but so the pipe will still be able to rotate. 5. Install the muffler mounting brackets to the frame using the single hole in the brackets and the stock hardware. The left side mounting bracket (stamped #206 on the bracket) mounts to the outside of the frame, where the stock muffler assembly mounted. The right side bracket (stamped #207) mounts to the inside of the frame, behind the stock muffler mounting point. 6. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (all supplied). Do this to each muffler but leave the clamp loose at this time. 7. To determine the difference between the left, right, upper and lower mufflers refer to the number stamped on the bracket welded to the backside of each muffler. The top right hand muffler is D500, the bottom right hand muffler is D510, the top left hand muffler is D550 and the bottom left hand muffler is D512. Note : The endcap bolts should face down and inward when viewing from the rear (Refer to Figure 1) .

1999-2001 Triumph Sprint RS Slip-On Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Loosen the clamp that holds the connector pipe to the headers under the bike. Remove the hardware that holds the stock muffler at the passenger footpeg bracket. Take off the muffler. 3. Re-using the stock Triumph clamp install the new S- bend. Leave loose for now. 4. Place a bead of the hi-temp sealant on the outside edge of the s-bend. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 5. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Place the spacer between the stock footpeg bracket and the tabs of the clamp. Locate both tabs of the canister clamp on the outside of the spacer. Use the hardware provided along with the stock nut to secure it. Leave loose for now. 6. Make sure everything is aligned and tighten all hardware. Affix the two connector springs to the muffler. 7. Be sure to allow the sealant to dry per the manufacture’s instructions before starting the bike . Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.

Aprilia RSV4 Exhaust Systems Installation instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
REMOVAL OF STOCK EXHAUST SYSTEM 1. 2. 5 Figure 3 Figure 4 Remove the metal collar and rubber damper from the stock muffler hanging bracket (Figure 3, 4). 3. 6 Unscrew the marked bolts and remove the plastic fasteners from the left and right side of the cowling (Figure 5, 6). 4. Figure 5 Figure 6 7 Unscrew the marked bolts and remove the lower part of the cowling (Figure 7). 5. Figure 7
8 Figure 8 Figure 9 Coat the bolt and interior of the metal clamp with spring hook whit Akrapovič anti-seize lead-free copper paste (black tube) and correctly install it onto the stock collector. Hand tighten the bolt (Figure 9, 10). WARNING: use anti-seize copper paste on bolt threads and interior of the metal clamp! 2. 1. Coat the bolt and interior of the metal clamp with Akrapovič antiseize lead-free copper paste (black tube) and correctly install it onto the link pipe (Figure 8). WARNING: use anti-seize copper paste on bolt threads and interior of the metal clamp

Incoming search terms: