Suzuki GSF 1200S Bandit Upgrade INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Holeshot Steering Damper 12 Then he attached a wire to the damper rod, to prevent it from getting lost in the fork tube, and pulled out the stock spacer and spring. 11 The Bandit has an internal damper that’s connected to the top and bottom of the fork tube. Kevin loosened the nut to detach it from the fork cap. 5 Rich loosened the damper body clamp and slid it onto the damper. 6 Next, he mounted the damper, front and rear, using a flat washer and a locking nut as a safety precaution. Then he began the final adjustments (see sidebar for details). When finished, he tightened the bolts in the fairing bracket. 7 To install the fork brace, Rich had to first carefully cut off the plastic fork protectors. 8 He placed the body of the brace between the forks and loosely bolted each end of the brace in place. He finished by tightening all the bolts to spec. 9 The Works Performance spring kit comes with everything needed for installation. 10 With the bike on the lift, Kevin jacked up the front end to reduce the spring load. He removed the bars, loosened the pinch bolts, and removed the fork cap. Holeshot Fork Brace Works Dual-Rate Spring Kit February/March 2006 RoadBike 87 www. RoadBikeMag.com February/March 2006 RoadBike 88 16 The Muzzys kit comes with the canister, a midsection pipe, and a centerstand stop plate and bolt. 17 I removed the stock muffler, starting from where the midsection pipe joins the header. If the gasket is in good condition, you can reuse it. 18 Since the stock pipe included a centerstand stopper, Muzzys provides a new one. With the muffler removed, I mounted the stop plate to the centerstand pivot bolt. 19 I carefully eased the Muzzys midsection pipe into the stock gasket, and then slid the muffler on and rotated it until the mounting brackets were aligned. 13 Kevin compared the stock spring assembly (bottom) to the Works one (top) to see if he needed to cut the provided spacer. There’s a difference of about .25″, but the instructions account for this discrepancy (years of the stock spring carrying a load), so no cutting was required.

Incoming search terms:

Honda CBR-600 F4 / F4i – Installation Instructions (slip-on)

0

Filed Under (Honda) by admin on 11-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the middle of the stock pipe. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Remove the clamp from the stock exhaust system and save for reuse. Install the S-Bend to the rear of the stock head pipe. Reuse the stock clamp, but do not tighten at this time. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 190-200mm from the edge of the end can. See figure 2 for details.
Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
Attach the supplied springs to fasten the end can to the S-bend pipe. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced prope rly on the can (refer to step 7 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system

Incoming search terms: