HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms:

HARLEY DAVIDSON ROAD ZEPPELIN SEAT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse following the instructions in the service manual. NOTE Cover the painted surfaces with protective material to prevent scratches or other damage. 2. Remove the left and right side saddlebags following the instructions in the owner’s manual. 3. See Figure 1. Remove the screw (1) and lockwashers (2) securing the grab strap (3) to the bracket (4 or 6). Save the hardware for installation. 4. Remove the grab strap. 5. Remove seat following the instructions in the service manual. -J04456 1 of 4 1 2 4 3 1 2 6 3 5 7 is06068 1. Stock screw 2. Stock lockwasher 3. Grab Strap 4. Bracket, 2009-Later Models 5.2009-Later Models 6. Bracket, 2008-Earlier Models 7.2008-Earlier Models Figure 1. Grab Strap and Saddlebag Front Mounting Bracket INSTALLATION 1. See Figure 2. Remove rubber plug from accessory connector (1) located under seat. Plug the seat electrical connector into the accessory connector. The connectors should lock together with an audible click. 2. Position the seat on the frame. Make sure the electrical harness and connector are not pinched between the seat and frame. 3. Install the seat following the instructions in the service manual.

HARLEY DAVIDSON VRSC CHROME BRAKE CALIPER INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
This kit fits 2006 and later VRSC model motorcycles.INSTALLATION 1. See Figure 1. Press in the upper tab (3) with a small screwdriver and remove the stock brake caliper insert (1) from the brake caliper (2). NOTE When installing the front caliper insert, position the single prong tab to the top of the caliper. When installing the rear caliper insert, position the single prong tap toward the front of the caliper. 2. Install the the chrome brake caliper insert into the brake caliper with the caliper oriented in the same manner as the stock insert. 1 2 3 is00627 1. Brake caliper insert 2. Brake caliper 3. Single prong tab Figure 1. Front Brake Caliper (VRSCR Model Shown

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly

SUZUKI M109 BRAKE PEDAL INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
1. Remove the pinch bolt from the bottom of the stock brake pedal. Notice that the slot in the pedal aligns with a punch mark on the end of the shaft. Using a needle- nose pliers disconnect the return spring from the pedal. Remove the pedal by sliding it outward until it touches the foot peg mount and then pushing the shaft inward. 2. Remove the pinch bolt from the new brake pedal and install it so that the slot is aligned with the punch mark on the end of the shaft. Install the pinch bolt and tighten it securely. Reconnect the pedal return spring

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms:

HARLEY DAVIDSON RIDER BACKREST MOUNTING HARDWARE KIT INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove seat according to the instructions in the service manual. 2. Remove the ECM caddy/battery cover by removing two screws. 3. See Figure 1 and Figure 2 for the mounting locations of the brackets. NOTE Some seats may limit the fore/aft mounting location of the backrest bracket. 4. See Figure 3 and Table 1. Remove plastic protective cap and locknut from stud. Leave the small plastic washer in place or the stud plate will fall out. With the backrest mounting bracket tab facing forward, attach the backrest mounting bracket (1) to stud plate with stock locknuts from the stud plate. 5. Tighten locknuts to 5-8 ft-lbs (6.8-10.8 Nm) . 6. Attach the front mounting bracket (6) to the frame cross- member using using two flange screws (8) and flange nuts (7). Tighten screws to 72 in-lbs (8.1 Nm) . 7. Attach the bracket support (2) to the front mounting bracket (6) with screw (8) and nut (7). 8. Install screw (5) and nut (9) to bracket support and backrest tab and tighten to 15 ft-lbs (20.3 Nm) . 1 2 is05475 1. Backrest mounting bracket 2. Front mounting bracket Figure 1. Bracket Mounting Locations 3 2 1 is05476 1. Backrest mounting bracket 2. Front mounting bracket 3. Bracket support Figure 2. Backrest mounted After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) -J04733 1 of 2
9. Install the ECM caddy/battery cover using two screws previously removed and tighten to 6-8 ft-lbs (8.1-10.8 Nm) . 10. Install seat according to service manual instructions. 11. Hold slit between rider and passenger seat open. On rider backrest, compress backrest rods and spring. Insert rods into backrest mounting bracket. Backrest Pad Adjustment 1. Adjust fore/aft position of backrest pad. Use 3/16 inch hex wrench to adjust set screw that is accessible through eyelet opening on rear of pad. If possible, do not remove set screw because it is difficult to install.

Incoming search terms:

KAWASAKI VOYAGER AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 27-12-2010

download
1. Remove the false fuel tank cover to expose the battery. Remove the right hand lower leg fairing. (4 phillips screws). Unplug the stock horn and remove the (2) 10mm bolts securing it to the frame. 2. See photo #1 using the stock horn bolts attach the black horn mounting bracket and the white ground wire supplied as shown. Next locate the relay supplied. Plug the stock horn wires into the relay terminals #85 & #86. (see wiring diagram on back side of instructions) 3. Attach the air hose to the compressor air outlet fitting. Attach the short red wire supplied to the compressors positive (+) terminal and the white wire installed earlier to the compressors ground (-) terminal. As shown in photo #2. Attach the compressor to the frame with the hose clamp provided. Note: position the top of the compressor as shown touching the bottom of the horn mounting bracket and approximately 1 Ω” to the rear of radiator and shroud. Also the air hose and fitting should be in front of the frame tube with the hose routed inside the hose clamp without pinching the hose. Attach the red wire from the compressor to one of the relays remaining outer terminals #30 or #87. Attach the remaining long red wire (supplied) to the remaining relay terminal #30 or #87. Secure the relay to the frame with a cable tie supplied. Route the red wire up to the battery positive (+) terminal. Locate the fuse wire assembly provided. Attach the fork end of the fuse wire to the battery positive (+) terminal. Cut the red wire to the desired length, strip the end and crimp to the fuse assembly. Turn on the ignition and press the horn button, you should hear the compressor motor run. Re-install the false fuel tank lid. Re-install the right lower leg fairing while routing the air hose out next to the black horn mounting bracket 4. See photo #3, Bolt the horn set to the black mounting bracket using the 5/16 x æ”bolt, washer and lock washer provided. Trim the air hose to length if necessary and attach the air hose to the horn assembly. Install the trumpet covers. (see instructions enclosed with covers) Turn on the ignition and test the horns

YAMAHA ROAD STAR PASSENGER FLOORBOARD RELOCATION ARMS INSTALLATION INSTRUCTONS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. If you are installing Relocation Arms and Passenger Floorboards, install the floorboards first per their instructions. When installing the Relocation Arms with Passenger Floorboards already installed proceed as follows. 2. Starting on the LEFT side, fold the floorboard up. Remove the socket head bolt which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which pinholes the dowel pins are located in. 3. Locate the Relocation Arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the pinholes in the backside of the arm that are directly across from one another. (180 degrees apart.) Place the arm onto the mounting block and align the pins in the arm with the holes closest to the desired height you wish the floorboard to be at. Bolt the arm to the mounting block loosely using one of the supplied 5/16″ X 1″ button head bolts. 4. Place the Passenger Floorboard with its two dowel pins into the set of pinholes at the other end of the relocation arm that allows the floorboard to be parallel (horizontal) to the ground. Use one of the supplied 5/16″ X 3/4″ socket head bolts to mount the floorboard to the relocation arm and make finger tight. 5. Install the RIGHT side in the same manner. Check to see that the right arm is at the same height and/or position as the left. Bolt the floorboard to the other end of the arm using the remaining dowel pins and socket head bolt. Tighten all four bolts on both sides securely. NOTE: Four other height positions are possible by using the other sets of holes on the front side of the mounting block and backside of the relocation arm

2007-2008 Ducati Hypermotard Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
1. Remove the seat. 2. Remove the fuel side panels. 3 Lay the PCIII near the battery and route the harness down the left hand side of the bike (Fig. A). PCIII harness 6 Plug the YELLOWcolored wires from the PCIII in-line of the rear injector and stock wiring harness (Fig. D). 7 Unplug the stock wiring harness from the front injector (Fig. E). This injector is located on the right hand side of the bike. 8 Plug the ORANGE colored wires from the PCIII in-line of the front injector and stock wiring harness (Fig. F). Fig. D Fig. E Fig

Incoming search terms: