2005-2010 TACOMA RUNNING BOARD REPAIR

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Remove Running Board from Packaging. (a) Remove running board assembly from package and place on a clean protected surface. The boards are sided (Fig. 1-1) (b) Verify kit contents and inspect the running board for damage. 2. Running Board Preparation for Installation (LH/RH Side). (a) Verify hardware bag content by referring to the cover page of this instruction sheet. (b) Loosen the 1/4 – 20 flange nuts at each of the three (3) bracket locations on each running board. (Fig. 2-1) (c) With a small slotted screwdriver, remove the plastic plugs covering M8 weld nuts in body of vehicle at 6 points/side.

Incoming search terms:

2005-2010 TACOMA CARGO DIVIDER Preparation and Bracket Installation

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Bracket Installation (a) Remove end caps from the back of each vehicle bed side rail. (Fig. 1-1) (b) Slide one clamp plate into each side rail. (Fig. 1-2) (c) Install the LH Bracket (with the WARNING label) onto the LH clamp plate threaded stud

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

TOYOTA AUTOMATIC TRANSMISSION SHIFT LOCK OVERRIDE BUTTON

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
AUTOMATIC TRANSMISSION SHIFT LOCK OVERRIDE BUTTON 2/3 ORB COVER STORAGE: The ORB is placed in a plastic envelope with a caution label and the envelope is taped to the automatic transmission shift lever as shown below: INSTALLATION OF ORB COVER: Install the ORB cover with the index facing toward the rear of the vehicle. PRODUCTION EFFECTIVE: MODEL PRODUCTION EFFECTIVE CAMRY FROM ’93 M/Y (AUGUST, 1992) COROLLA FROM ’93 M/Y (JUNE, 1992) TERCEL, PASEO FROM ’93 M/Y (AUGUST, 1992) CELICA FROM ’93 M/Y (AUGUST, 1992) LAND CRUISER FROM ’93 M/Y (AUGUST, 1992) TMM CAMRY FROM ’93 M/Y (AUGUST, 1992) TMMC COROLLA FROM ’93 M/Y (SEPTEMBER, 1992) NUMMI COROLLA FROM ’93 M/Y (AUGUST, 1992

Incoming search terms:

HARLEY DAVIDSON LUGGAGE RACK BAG INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION 1. Set the rack bag on top of the luggage rack with the main pocket opening facing the rear of the vehicle. 2. See Figure 2, Figure 3 and Figure 4. Determine which luggage rack is installed on the vehicle. 3. See Figure 1. Open the hook-and-loop closures in the appropriate locations for the installed luggage rack. 4. Fasten the closures around the bars of the luggage rack and pressing the hook-and-loop ends together. 5. Give the rack bag a final pull to verify the pack is securely attached. 1 2 3 4 7 5 6 is05516 1. Rear left closure 2. Rear center closure 3. Rear right closure 4. Front left closure 5. Front center closure 6. Front right closure 7. Rain cover storage Figure 1. ook-and-Loop Closure Locations 1 2 3 4 5 6 is05513 Figure 2. Premium Rack Closure Locations -J00861 1 of 2 1 3 4 6 is05514 Figure 3. Air Wing Rack Closure Locations 2 5 4 6 is05515 Figure 4. Contoured Rack Closure Locations USAGE Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) •Combined load of top rack and Tour-Pak® must not exceed 25 lbs (11.3 Kg). Overloading the motorcycle will cause unstable handling and reduced braking efficiency, which could result in death or serious injury. See Figure 1. Open the hook-and-loop flap on the rain cover storage pocket (7) and wrap the tethered rain cover around the bag.

Incoming search terms: