HARLEY DAVIDSON TALL HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION Preparation Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. Remove the outer fairing. See UPPER FAIRING/WINDSHIELD (FLHX, FLHT/C/U), OUTER FAIRING/WINDSHIELD, REMOVAL in the Service Manual. Remove the fairing cap. See UPPER FAIRING/WINDSHIELD; FAIRING CAP: REMOVAL in the Service Manual. 3. Bleed the brake fluid from the front brakes per the instructions in the Service Manual. Original Handlebar Removal NOTE Cover the front fender and the front of the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Models WITH radio: Remove the radio. See RADIO: REMOVAL in the Service Manual. Models WITHOUT radio: Remove the storage box. a. The four socket head screws fastening the storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. Use a long shank ball-end socket to remove the screws. b. Pull the storage box forward to remove it from the opening in the inner fairing. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Disconnect the front brake lines from the vehicle. See FRONT BRAKE MASTER CYLINDER, FRONT BRAKE LINE, REMOVAL, FLHX, FLHT/C/U in the Service Manual

HARLEY DAVIDSON FLHT ADVANCED AUDIO AM/FM/CD RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Remove Existing Equipment To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove outer fairing and windshield. Refer to OUTER FAIRING/WINDSHIELD REMOVAL in Service Manual. 3 2 1 is 00397 1. Socket head screw (4) 2. Radio support bracket (2) 3. Radio Figure 1. AM/ FM Radio Installation 3. See Figure 1. Using a long shank ball end socket (Snap- on® FABL6E or equivalent), remove the four socket head screws (1) to release the storage box from the left and right radio support brackets (2). Use the oblong holes in the fairing brackets to access the screws. Install Radio 1. Pull the storage box forward to remove the box from the opening in the inner fairing. Discard the storage box. 2. Position the radio (3) between the radio support brackets and push it into the opening in the inner fairing. 3. Align the threaded inserts in the sides of the radio with the oblong holes in the left and right radio support brackets. 4. Starting at the rear, install the four socket head screws previously removed. Alternately tighten the screws to 35- 45 in-lbs (4.0-5.1 Nm). 5. Plug the 23-place radio socket housing [27A] (part of the interconnect harness already installed on the vehicle) into the back of the radio. 6. Remove three T25 TORX® screws that hold the speaker opening cover on one end of the fairing. Discard the cover and screws. Install Speakers 1. See Figure 3. If the speaker (3) and adapter (4) are not assembled, or are assembled incorrectly, orient the speaker on the adapter and grille assembly so the speaker spade contacts are toward the side of the adapter with the widest edge. Snap the speaker into the adapter using finger pressure only.

Incoming search terms:

VICTORY BLACK LIGHT LEAK DETECTOR KIT

0

Filed Under (Victory) by admin on 31-10-2010

download
AMMCO HONE KIT Rigid hone to correct tapered and out of round cylinders. Range: 47.6 mm – 69.8 mm (1 7/8″ – 2 3/4″). Contains 60 and 220 grit stones, driveshank with depth stop and metal storage box. Oversize stone kits increase range to 92 mm ( 35/8″). Replacement Stone Kits are shown below. All stones shown below are included in the kit including the new PU-49876. 2870304 – REPLACEMENT STONE KIT – 60 Grit (47.6 0 69.8mm) 2870305 – REPLACEMENT STONE KIT – 220 Grit (47.6 – 69.8mm) 2870306 – REPLACEMENT STONE KIT – 60 Grit (69.8-92.8mm) 2870307 – REPLACEMENT STONE KIT – 220 Grit (69.8 0 92.8mm) 2871536 – REPLACEMENT STONE KIT – 69.8 for Ni-Ca-Sil deglazing PU-49876 – 320 GRIT REPLACEMENT STONE SET 2870386 PISTON PIN PULLER Removes 18 mm piston pins from all Polaris pistons. Required for many Polaris puller attachments. Note: Some engines require adapters. Available Adapters: 2871342 2871445 2870390 PISTON SUPPORT BLOCK Safely supports piston while disassembling or assembling engine top end. 2870569 CRANKSHAFT TRUING STAND For holding crankshaft while checking runout for all Polaris engines. 2870588 HONING OIL 12 oz can with dispensing tip. Promotes better finishes, faster cutting and longer stone life. Engine VICTORY 83 PU-46219 OIL EXTRACTOR Used to draw the engine oil from the crankcase. PV-35457 BLACK LIGHT LEAK DETECTOR KIT The Black Light Oil Leak Detector provides an effective time saving method for pinpointing engine oil leaks. Simply add 1 oz. of fluorescent oil additive to the engine crankcase (6 – 1 oz. bottles included). Run the engine for ten minutes to circulate the fluorescent oil additive throughout the engine. Oil leak will fluoresce a bright yellow when illuminated with PV-35457 Black Light. Includes: Fluorescent Black Light PV-28431-6 Oil Additive (6) 1 oz. Bottles (available separately) PV-28431-6 – LEAK DETECTION DYE PV-35667-A CYLINDER LEAKDOWN TESTER PV-35667-A will test for worn piston rings, cylinder walls, valves, gaskets and any other related leakage problems. Uses shop air. M12 x 1.25 Adapter and instructions included. PV-39951-A ENGINE TACHOMETER This digital tachometer accurately measures engine RPM and maximum RPM of 2 or 4-stroke engines. The dual display allows for readings of current RPM alone or current and maximum RPM. Also features two maximum RPM memories for comparison

Incoming search terms: