HONDA GL 18001-RP Illuminator Replacement Lamp Set Installation Instructions

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the plastic caps covering the brake and clutch master cylinder clamp bolts, remove the clamp bolts and clamps. Pull the master cylinders away from the handlebars and let them rest on the fairing storage compartment covers. 2. Using a heat gun or a hair dryer warm up the old lamps one at a time until they are hot to the touch then carefully peel them away from the switch housings. 3. Remove any remaining adhesive from the old lamps left on the housings using rubbing alcohol. Locate the wire harness to the lamp connectors covered with heat shrink tubing. Using a sharp knife carefully cut the heat shrink tubing open lengthwise. Carefully taking caution to not cut the wires, peel the heat shrink tubing open, then away and off the connection. Unplug the lamps from the harness. Replace any of the gold pin connectors on the harness if needed with the new ones supplied. 4. Slide the heat shrink tubing over the gold pins and wire harness ends. Carefully plug the gold pins from the harness onto the lamp connectors (NOTE: the metal connectors on the lamps can break if bent from side to side).Turn on the ignition and verify that all three lamps are working. Slide the heat shrink tubing over the connections and shrink using a heat gun, hair dryer or lighter being careful not to melt the lamp ends. 5. Using your heat gun or hair dryer warm one of the switch housings and the matching lamp so that they are hot to the touch (about 140 degrees). Peel the backing from the lamp, carefully place in position, press firmly onto housing, wrap the tail of the lamp with the wires around the housing and then rub over the entire lamp firmly several times to ensure good adhesion. 6. Reassemble the master cylinders and clamps onto the handlebars being careful not to pinch the wires or lamps.

Hammerhead La Vita 150cc OWNERS MANUAL

0

Filed Under (Hammerhead) by admin on 27-11-2010

download
1. Left and Right rear Mirror 2. Left and Right Brake 3. Front storage compartment (option) 4. Speedometer/ Digital Gauge 5. Main Switch 6. Battery 7. Air Cleaner 8. Seat Lock 9. Rear Light Assembly 10. Left and Right Rear turn Lights 11. Fuel Tank 12. Center Stand 13. Kick Start 14. Side Stand 15. Muffler 16. Left and Right Turn Lights 17. Head Lights 18. Rear Reflector Instrument Panel Speedometer Riding speed is indicated by KM/H and MPH. Odometer The total riding distance is in KM and Miles. The black figures in black background indicate total miles traveled. Indicating lamp or turning light It flashes when turning light is in use. Fuel Gauge Fuel Gauge indicates the remaining fuel in the fuel tank (the gauge does not work when main switch is in the “OFF” position). The gauge moves from “F”(full) to “E” (empty) as fuel decreases in the fuel tank. Fill the tank with 90 Octane or higher gasoline when the needle is approaching the “E” position. There is no reserve tank. Indicating Lamp of High beam It indicates high beam is in use. Note: apply low beam to avoid obstructing the view of oncoming drivers and drivers ahead. 1. Speedometer 2. Odometer 3. Left turn signal indicator 4. Right turn signal indicator 5. High beam indicator 6. Fault signal indicator 7. Battery Gauge 8. Fuel Gauge Instrument Control Main Switch NOTE: – Do not leave the main switch in “ON” position for an extended period of time when the engine is stopped. The battery may drain itself empty. – Lock the steering and remove the key after park to avoid theft. “ON” Position: Electric Circuits are switched on. The engine can now be started. The key can not be removed in this position. “OFF” Position: All electrical circuits are switched off. The engine stops. The key can be removed in this position. “LOCK” Position: The steering is locked when in this position. The key can be removed. Steering Lock Turn the handle bar fully to the left to lock the steering to prevent theft. Push the key in when it is in “OFF” position and while pushing the key in, turn the switch to “LOCK” position to lock the steering. Pull the key out once you are done

Piaggio MP3 125 Specification

0

Filed Under (Piaggio) by admin on 11-11-2010

download
Capacity 125cc (EURO 3) Engine LEADER 4 valve, 4 stroke single cylinder Cooling Liquid Electric Starter * Transmission Automatic Twist and Go Front Suspension Parallelogram, cantilever Rear Suspension Twin hydraulic shock absorbers with pre-load adjuster Front Brake Disc Double Ø240mm disc Rear Brake Disc Ø240mm disc Wheel Size 12″-12″ Running Weight 208 kg Lockable Glove Box * Underseat Storage Compartment * Digital Clock * Colours Available Sky Blue, Excalibur Silver, Black Graphite, Cherry Red

Piaggio MP3 250ie 250cc specification

0

Filed Under (Piaggio) by admin on 11-11-2010

download
Capacity 250cc (EURO 3) Engine QUASAR 4 valve, 4 stroke single cylinder with electronic injection Cooling Liquid Electric Starter * Transmission Automatic Twist and Go Front Suspension Parallelogram, cantilever Rear Suspension Twin hydraulic shock absorbers with pre-load adjuster Front Brake Disc Double Ø240mm disc Rear Brake Disc Ø240mm disc Wheel Size 12″-12″ Running Weight 213 kg Lockable Glove Box * Underseat Storage Compartment * Digital Clock * Colours Available Sky Blue, Excalibur Silver, Black Graphite, Cherry Red

Incoming search terms: