HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms:

HARLEY DAVIDSON DYNA STREET PERFORMANCE SLIP-ON ACCESSORY MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meets all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for purposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 2. Loosen stock muffler clamps and remove nuts that attach mufflers to muffler support tube. Remove stock mufflers. Save all mounting hardware for reinstallation. 3. Install new kit mufflers using muffler clamps (purchased separately) and stock mounting hardware saved from Step 2. Do not tighten hardware at this time. NOTE Before tightening nuts that attach mufflers to muffler support tubes, make sure the front muffler is positioned as far forward in its brackets slot as possible. This will eliminate any possible contact between the mufflers. 4. Tighten muffler clamp bolts to 45-60 ft-lbs (61-81 Nm) . Tighten nuts that attach mufflers to muffler support tube snugly. 5. Connect the negative (-) battery cable

Incoming search terms: