CFC Offroad KTM RFS (Racing Four Stroke) Clutch Cover 250-400-450-520-525 EXC-XC-SX Installation and Removal Manual

0

Filed Under (KTM) by admin on 30-01-2012

download
1. Wash engine sidecase to remove any dirt, grease, oil, etc. 2. Clean engine sidecase and the CFC case guard with quick drying solvent such as electrical contact cleaner or brake cleaner 3. Apply an even layer of Permatex 16B silicone adhesive* to the backside of the CFC guard. This can be a messy job and most find the best tool to spread it evenly is your finger. It is suggested that you use a rubber glove to avoid skin contact. Try to get complete coverage free of voids and about 1/16-1/8″ thick 4. Align sidecase Guard with the engine sidecase, keeping the logo horizontal (if the Guard has one). Gently press on the engine sidecase. Once you feel that it is aligned and positioned properly, press with enough evenly distributed pressure to get an equal squeeze out of Permatex all around the perimeter. Don’t worry if you end up with excess. Excess adhesive can be cleaned up with a rag and mineral spirits or brake/contact cleaner. Let dry overnight 5. A couple of strips of masking tape can be carefully applied to assure the guard doesn’t move

STROKE DOWNHILL MOUNTAIN BIKE SHOCK SPECIFICATIONS

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
The shock has an adjustable rebound and standard Hi/low compression. The optional independent hi/ low compression adjuster has a low speed brass screw and a seperate blue high speed hex. The rebound adjuster is at the bottom of the shock. The standard setting is 8 clicks out (counter clockwise) from full hard. To increase rebound damping turn the adjuster in (clockwise), this will slow the extension of the shock. To decrease rebound damping turn the adjuster out (counter clockwise) this will quicken the extension of the shock. The standard compression adjuster has a the slotted brass screw on the reservoir. The standard setting is 12 clicks out low/hi speed brass screw(counter clockwise) and 1.75 turns out on the blue hex high speed adjuster from full hard. To increase compression damping turn the adjuster in (clockwise) – this will stiffen the compression of the shock. The low speed compression adjuster will soften small bumps and improve traction. The optional high speed adjuster will firm up the damping for big hits with no loss in small bump compliance, firmer settings will improve pedaling as well, lighter settings will smooth out square edge hits. Spring preload can also be changed to tune the shock to the weight of the rider. The shock spring preload can be varied by tightening or loosening the preload collars. The standard preload is 1.5 turns, (min 1 turn / max 3 turns). The rider sag must be adjusted to 1/3 of the total stroke with the rider sitting on the bike. This is the difference from fully extended position to the rider sitting. The ride height can be raised or lowered ± 5 mm to quicken or slow steering within the range of preload settings

AUTOMOTIVE BRAKE BLEEDING KIT MODEL MV8020 USER'S MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
MOTORCYCLE BLEEDING PROCEDURE Before bleeding the system, ensure that: 1) The brake caliper pistons are free to move within the calipers. 2) The master cylinder piston is free to return to the end of its stroke, and 3) Inspect the line to ensure that all fittings are tight. FRONT BRAKE 1) Pump brake lever to seat caliper pads against rotor. 2) Cover gas tank with plastic protective sheet if using DOT 3 fluid (not necessary if using DOT 5 fluid). 3) Remove master cylinder reservoir cap and fill reservoir. 4) Select the appropriate adapter(s). The L-shaped universal adapters should fit snugly over the brake bleeding fitting in order to seal properly. The tapered adapters fit inside the thru-hole of fitting and will generally seal well when inserted tightly with a pressing and twisting motion. Attach adapter to reservoir hose. 5) Pump several times to create vacuum. Crack bleeder valve with box wrench, extracting fluid into reservoir. (Stop and add fluid when master cylinder begins to get low. Do not allow air to enter line.). At this point, all air should be out of system and line full of fluid. (Note: if air is entering the pump hose from around bleeder fitting, remove bleeder fitting and apply Teflon tape to threaded portion of bleeder screw only. This will prevent air seepage around threads of bleeder screw.) 6) While maintaining vacuum on the pump line, tighten bleeder fitting. 7) Top off reservoir and reinstall cover. Check brake by pumping lever several times. Pedal should have a positive, solid feel. If not, repeat bleeding process as more air may have entered the system. Inspect line to ensure all fittings are tight. If brake still feels slack, consult a service technician.

AJS NAC12 Specifications

0

Filed Under (AJS) by admin on 12-11-2010

download
Engine type ………………….. 4 stroke, twin cylinder, liquid cooled Cylinder capacity …………… 124cc Bore x stroke ………………… 44mm x 40mm (x2) Starting method ……………. Electric Transmission ………………… 5 speed gearbox, Chain drive. Clutch ………………………….. Wet, Multi-plate Ignition ……………………….. Coil CDI Battery ………………………… 12v Tyres F <> R ………………… Tubeless 90/90 – 18 <> 130/90 – 15 Suspension F / R …………… Tele’ forks / twin rear shocks Brakes F / R …………………. Twin disc / disc Fuel tank capacity …………. 18 litres Seat height …………………… 77cm (30.5″) Wheel base …………………… 151cm Max power net (approx) …. 8.5kw @ 10’500 rev/min Dry weight …………………… 153kg Max load ………………………. 150kg Noise Level (drive by) …….. 77db(A)