YAMAHA CRANKSHAFT LOWER END REMOVAL AND INSTALLATION TOOLS

0

Filed Under (Yamaha) by admin on 08-01-2012

download
90 LOWER END REMOVAL & INSTALLATION TOOLS SHOP EQUIPMENT & TOOLS 35-8399 35-8513 35-8516 35-8508 35-8504 35-8507 YAMAHA CRANKSHAFT PROTECTORS Sold each. 35-8504 YM-4063-A, XV750/920 Virago, XT550, YFP350, YFM660R Raptor 35-8399 YM-1382, XT250/XT350, RZ350, YFP350, YFZ350 35-8507 YM-33282, XV500 Virago, XZ550 Vision, XVZ12/13 Venture & Venture Royale, VMX12 V-Max 35-8508 YM-38145, XV750/XV1000 Virago YAMAHA CRANKSHAFT INSTALLATION SET Sold as a set. Consists of the following: Qt1-Installing Pot, Qt1-Pot Spacer, Qt1-Bolt. 35-8509 YU-90050 Crankshaft Installation Set OPTIONAL POT SPACERS 35-8513 YU-90070-A, XV750/920 Virago, XT550, TT600 35-8515 YU-91044, YFM350, SRX600, XT550/600 35-8516 YU-1202, SR500, TT/XT500 CRANKCASE PRESSURE TESTER An accurate method for checking possible air leaks on two-stroke engines. Complete with air pressure gauge, pump-up bulb and all fittings and adapters for single and multi-cylinder two-cycle engines. 35-5962 Crankcase Pressure Tester CRANKSHAFT INSTALLING JIG TOOL Supports and centers crankshaft webs while assembling two-stroke engine cases and rebuilding crankshafts. Prevents rod misalignment. Adjustable tang ends. 35-9804 Crankshaft Installing Jig Tool CRANKCASE SEPARATOR TOOL This tool will work on most two and four stroke engines that have a vertically split crankcase. Moveable fingers allow a multitude of bolt patterns to be used so it will work on a variety of models. Includes 6mm and 8mm mounting bolts, center pulling bolt and a three leg frame that is appropriate for many applications. 35-9642 Crankcase Separator Tool 35-9637 Replacement 6mm and 8mm mounting bolts. Each

Incoming search terms:

HONDA CR250R Owner’s Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
l. CONTROLS( 1 ) Frontbralte tever (2) Throttle grip ( 3 ) Engine stop switch When shutting off engine, press in the  engine stop switch button. (4 ) Rear brake pedal ( 5 I Kickstarter pedal ( 6 } Clutch lever (1′) Fuel tank filler cap ( 8) Gear change pedal The transmission has S speeds. Depress the pedal to Shift into [st gear. Raise the pedal to shift into 2nd, 3rd, 4th and 5th. Neutral is located between 1st and 2nd.  9 ) Fuel mixture enrichment l-mob When starting a cold engne, raise the fuel mixture knob and fully depress the kickstarter pedal. (10) Fuel valve When the fuel valve is turned to "OFF", fuel cannot Flow from the fuel tank to the carburetor. When the fuel valve is turned to “ON”, fuel will flow from the tank to the carburetor. (1 1] Rear shock absorber adjuster The rear shock absorber springs have three settings for precise adjustment of the rear suspension to suit riding conditions and differences in rider weight. Page 6 2 l. OPERATING – Fig. l—2 (1) Fuel tank -  2. FUEL The Honda CRZSUR ELSINORE has a two-stroke engine that requires a gasoline-oil mixture. The capacity of the “fuel tank is 8.59 (2.2 US gal. 1.9 Imp. gal). I Any automotive gasoline with :1 pump octane number of 86 or higher. or research octane number of9i or higher‘ may he used. If “l ofgasoline or a higher octane grade. USE HONDA 2-STROKE INJECTOR OIL OR EQUIVALENT. I Premix gasoline and oil in a ratio of   20:1 Prepare the fuel mixture in a clean container, and shake until thoroughly mixed before Flling the fuel tank. i Too much oil will muse excessive smoking and spark plug fouling. Too little oil will cause engine damage or premature wear. Mix fuel in a ratio of 20 parts gasoline to 1 part oil. I Vegetable oils separate from gasoline more easily than mineral oils, especially in cold weather. It is advisable to use mineral oil when ambient temperatures of below 0°C (32°F) are expected. I If the gasoline-oil mixture is left standing in a container for a long period of time, lubricity will deteriorate. Use the mixture within 24 hours. I Once an oil container is opened, the oil must be used within one month, since oxidation may occur. Do not mix vegetable and mineral oils. Gasoline is flammable and explosive under certain conditions. Always stop the engine and do not smoke or allow open flames or sparks near the motorcycle when refueling

Incoming search terms:

KINROAD 150 SERVICE MANUAL

0

Filed Under (Kinroad) by admin on 27-11-2010

download
FUEL AND OIL RECOMMENDATIONS Be sure to use the specified fuel and oil. FUEL Gasoline should SAE 90# or higher. Unleaded gasoline is recommended. ENGINE OIL SAE10W-30 engine oil of high quality should be used. BREAK-IN PROCEDURE For the first 2 hours of riding, do not exceed 2/3 throttle. Vary engine speed for the first 5 hours. Never hold engine at full throttle for long periods of time. SPECIFICATIONS DIMENSIONS DOUBLE SEAT/SINGLE SEAT Overall Length 2159mm/2075mm Overall Width 1400mm/1235mm Overall Height 1470mm/1400mm Wheelbase 1499mm/1450mm Ground Clearance 170mm/130mm ENGINE Type Forced air-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.5cc Bore x Stroke 57.4mm x 57.8mm Compression Ratio 9.2:1 Max Power 7.4kw/7500rpm Max Torque 9.5N.m/5500rpm Fuel Type SAE 90# or above (unleaded) Lubricate Oil SAE 10W/30 Ignition C.D.I. Starting Electric Spark Plug C7HSA (NGK) Transmission Automatic C. V. T. Carburetor MIKUNI, BS24J Lubrication Force & Splash

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

ATK NX 250 SPECIFICATION

0

Filed Under (Atk) by admin on 16-11-2010

Model: ATK NX 250 Category: Enduro / offroad Rating: Do you know this bike? Click here to rate it. We miss 2 votes to show the rating. Engine and transmission Displacement: 249.00 ccm (15.19 cubic inches) Engine type: Single cylinder, four-stroke Valves per cylinder: 4 Fuel system: Carburettor. Keihin 24mm Fuel control: DOHC
Ignition: CDI Lubrication system: wet sump Cooling system: Liquid Gearbox: 6-speed Transmission type,
final drive: Chain Clutch: wet plate Exhaust system: Supertrapp Chassis, suspension, brakes and wheels
Front suspension: WP USD Rear suspension: WP Multi Adjuster Shock Front tyre dimensions: 80/100-21
Rear tyre dimensions: 100/100-18 Front brakes: Single disc. 2-piston calipers Front brakes diameter: 24 mm (0.9 inches) Rear brakes: Expanding brake (drum brake) Physical measures and capacities Dry weight: 128.0 kg (282.2 pounds) Alternate seat height: 940 mm (37.0 inches) If adjustable, highest setting. Overall length: 1,473 mm (58.0 inches) Overall width: 820 mm (32.3 inches) Ground clearance: 323 mm (12.7 inches) Wheelbase: 1,473 mm (58.0 inches) Fuel capacity: 8.70 litres (2.30 gallons) Oil capacity: 1.80 litres (0.12 quarts) Other specifications Color options: Blue Frame – Red tank – White Fenders – 1 Inox radiatorcap Comments: Uses a Honda 4-stroke engine. Further information Parts and accessories Check out parts and

YAMAHA YZ MOTOCROSS ENGINE specification

0

Filed Under (Yamaha) by admin on 13-11-2010

download
YZ450F Engine Reshaped intake ports The YZ450F’s innovative 5-valve cylinder head design is one of the most sophisticated in the category, and plays a vital role in enabling this high-tech MX bike maintain its well-documented superiority on the race track. For 2008 the combustion efficiency of this advanced cylinder head is further improved with the introduction of reshaped intake ports which enhance the bike’s low to mid-range performance. New exhaust camshaft profile Yamaha Motor Europe N.V. Page 5 of 33
In order to optimise the significant performance gains of the new intake port design, the latest YZ450F’s 5-valve cylinder head is equipped with new camshafts featuring reshaped Yamaha Motor Europe N.V. Page 6 of 33
profiles. The inlet valve timing has been adjusted, the overlap is modified and exhaust lift is revised to create an idealised balance of intake and exhaust operations for increased combustion efficiency and improved performance in the important low to mid-range zone. Reduced piston clearance The YZ450F powerplant is already one of the most advanced 4-stroke engine designs in the MX world, featuring cutting-edge technology which gives it a real advantage. Extensive use of lightweight materials has enabled Yamaha to create a light, compact and high-revving engine which produces a remarkably wide band of hard hitting power – and for 2008 our engineers have further reduced cylinder/piston tolerances of the 95mm diameter piston in order to enhance the overall package. These reductions may only be measurable in terms of microns, yet the differences are most definitely tangible, and include increased torque output, smoother running and quieter operation. New 94dB silencer Complying with the new FIM94dB(A) regulations is a new stainless steel silencer which maintains the machine’s strong low to mid-range power output, while reducing overall noise.

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

2004-2007 Kawasaki STX-15F Supercharger Kit installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
ENGINE REMOVAL: 1. Turn ignition off, remove lanyard, disconnect battery cables and remove battery. 2. Remove engine following steps outlined in section 7 of Kawasaki service manual. NOTE: Replace oil filter if engine was run previously. Please recycle used oil and oil filter. NOTE: Clear an area on a sturdy workbench or heavy-duty cart to place engine after removal. Be sure to carefully place engine on a smooth surface so as not to damage oil pan. It is recommended that you have assistance for the engine removal process. 3. Replace stock pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket with supplied forged pistons, rings, piston pins, clips, cylinder head gasket and cylinder base gasket following the steps outlined in section 6 of the Kawasaki service manual. NOTE: This is an involved process requiring advanced mechanical skills and 4-stroke engine experience. DO NOT ATTEMPT if you are not mechanically inclined or familiar with 4-stroke engines. 4. Remove OE crankshaft coupler and discard. 5. Locate boss on PTO housing just above crankshaft. Cut off at a 45° angle. (See page 1 of Installation Images) NOTE: Cover end of crankshaft. Thoroughly clean engine afterwards. EXHAUST SYSTEM MODIFICATIONS: 6. Inside hull under rear grab handle remove air inlet tubes. Disconnect hoses for stock bilge pick-ups from breather fittings. (see illustration #1) 7. Remove exhaust hose connecting primary muffler (left water box) to secondary muffler (right water box). Disconnect remaining hoses from breather fittings. Remove exhaust hose connecting secondary water box to exhaust outlet. (see illustration #2) NOTE: Retain hose clamps. 8. Remove section of foam between top deck and pump area and discard. 9. At rear of hull remove and discard plastic exhaust outlet nozzle. Remove exhaust outlet, cut 5-3/4″ from end of flange and weld a bead around modified end of exhaust outlet. (see illustration #3) NOTE: Sand or file edge after modifying. 10. Install one supplied silicone coupler onto modified exhaust outlet and secure using OE hose clamp. (see illustration #4) Install exhaust outlet into hull and secure using stock hardware. (see illustration #5) NOTE: Be sure rubber gasket is in place between flange and hull. Do not use any sealant. Apply blue Loc-tite to bolts. Do not over tighten bolts. 11. Install supplied billet exhaust outlet tip using supplied hardware. (see illustration #6) NOTE: Apply blue Loc-tite to bolts. Do not over tighten bolts.

Incoming search terms:

Incoming search terms: