BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).