HARLEY DAVIDSON "LIVE TO RIDE" HANDLEBAR GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
installation Do not lubricate the left grip of handlebar in any way before installation. This could allow grip to come off while riding which could result in loss of control of vehicle and death or serious injury. 1. Remove existing left handlebar grip by carefully cutting it away from the handlebar using a sharp blade or knife. Remove right grip/throttle sleeve assembly following instructions in appropriate Service Manual. After removal, make sure that left and right handlebar ends are clean and smooth. 2. Check that end caps are securely fastened to grips. Tighten screw inside grip to secure end caps. 3. Assemble new throttle sleeve to handlebar. Refer to appropriate Service Manual for detailed procedure. NOTE Surfaces to be glued must be clean, dry, and free from oil. If surfaces are not clean, dry, and free from oil, then the new application may not adhere as desired. Please observe the following WARNINGS when using the adhesive contained in this kit. FLAMMABLE, INJURIOUS TO EYES, HARMFUL IF SWALLOWED, VAPOR HARMFUL. FLAMMABLE: CONTAINS METHYL ETHYL KETONE. Use only in well ventilated areas. Avoid contact with eyes, mucous membranes, and prolonged skin contact. KEEP OUT OF REACH OF CHILDREN. If swallowed, do not induce vomiting. Call a physician immediately. This product contains a chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm. 4. Liberally apply a coating of Harley-Davidson Adhesive (Part No. 99839-95) to the inside of left handlebar grip using the cotton swab. Make sure adhesive fully covers all inside surface area of the grip. Also, apply a coat of adhesive to the handlebar end. 5. Check how the rectangular pattern is oriented on the throttle (right) grip. Align pattern on left grip to match right grip and immediately push the new grip completely onto handlebar end. 6. Rotate the end caps so the “Live to Ride”text is positioned at the top of both grips. NOTE Do not hesitate when installing left grip or adhesive will dry before installation is complete. Allow 6-8 hours at 70°F to achieve full cure of the adhesive. Prior to starting engine, verify that the throttle control will snap back to the idle position when released. A throttle control that prevents the engine from automatically returning to idle can lead to a loss of control of vehicle which could result in death or serious injury. Cleaning

Incoming search terms:

HARLEY DAVIDSON WHEEL BEARING REMOVAL AND INSTALLATION TOOL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
BEARING REMOVAL 1. Place the wheel vertically in a vise and protect the rim from being marred. NOTE See Figure 1 for the tool lubrication locations before using. 2. Assemble the remover tool. a. Install wheel bearing puller (1), (2) or (16) depending on the bearing I.D. See the service parts table for the size reference. Install the wheel bearing puller into the bearing by hand or use a rubber mallet ( not a hard-faced hammer) to push through the bearing I.D. Stop pushing on the bearing puller as soon as it has cleared the inside of the bearing race. There will be a slight click. b. Place main body puller (3) over bearing puller with the fingers of main body puller facing the wheel. Lightly oil all threads. c. Place the large brass washer (10) and nut (13) onto the puller and hand-tighten the nut until it stops at the top face of the bridge. 3. Remove the front wheel bearings. a. Apply a small amount of oil to the taper at the hex end of the expander dowel. Insert the expander dowel (7) through the other side of wheel bearings, and through the bearing puller. b. Install the washer (15 and nut (14) to the expander dowel and torque to 100 in-lbs (11.3 Nm) with a 11/16 inch wrench or socket while holding the other side of the expander dowel by reaching the opposite side of the wheel with a 3/8 inch hex key. c. Align the main body puller support fingers centered over the bearing to be removed. If main body puller will be directly on a finished chrome surface, protect the surface area. d. If resistance is felt with a torque wrench set at 40 ft- lbs (54.2 Nm) of torque, you will need to apply heat to the hub area surrounding the bearing. Prior to applying heat, place 2 to 3 temperature stickers (P/N 94146-10) around the circumference of the hub. Apply indirect heat using a heat gun. Do not exceed 210°F. With a 1-1/8 inch socket and torque wrench, turn the nut (13) until the bearing is pulled free from the wheel hub. e. Using a 3/8 in. hex key on an extension and torque wrench set on the expander dowel (7) and a 1-1/8 inch wrench. Turn the nut (13) until the bearing is free of the wheel hub. 4. Remove the wheel bearing spacer from the I.D. of the wheel hub. 5. Repeat steps 1 through 4 for the opposite bearing. NOTE Remove rear wheel belt sprocket before removing the bearings. 6. Rear wheel bearing removal is the same as steps 1 through 4 by using the correct size wheel bearing puller

Incoming search terms:

Incoming search terms: