Suzuki M 109 WINDSHIELD INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 18-02-2012

download
Position the motorcycle securely on its stand or a work stand. Cover the front fender and fuel tank with a cloth to avoid scratches from dropped tools. 1. Use the above diagram toidentify left from right Lower and Upper Mount Brackets. Figure 1 2. Cut each of the clamp spacers in half to make 8 pieces, each 2.5 x 1.55″. 3. Apply one spacer to the inside of each mount bracket. Figure 2 Figure 1 Figure 2 N28201 and N28202 WINDSHIELD INSTALLATION AND OWNER’S MANUAL for Suzuki®M109 Right and Left side of Motorcycle is determined while sitting on the bike. Determine left from right Upper bracket. Washer angles inboard about 5 degrees. Note, Angle distinguishes Right from Left Lower Mount Bracket 1 2 4 3 5 6 8 9 10 National Cycle, Inc. Maywood, IL 60153-0158 USA 708-343-0400 / Fax: 708-343-0625 www.nationalcycle.com / e mail:info@nationalcycle.com Page 1 of 3 10-114056-000 08/07 / Rev B. 03/08 7 3, Left Upper Bracket 4, Right Upper Bracket About 5 0 inboard angle
INSTALLATION Measurements provided for clamp location. From this point you can adjust the brackets 1″ (22mm) higher if you prefer keeping in mind, position of the front nose of windshield should have a minimum of 1/2″ (13mm) clearance from cowling . Figure 3. Right Side Lower Mount Assembly 1. Start on the Right Side of motorcycle. At the top of the fork, place one inner black clamp on the fork tube. Figure 4 2. Hook the RIGHT SIDE lower mount bracket (2) to the inside clamp. Figure 5 3. Slide assembly down fork so bottom edge of bracket is 1.75″ (44mm) from top of lower triple clamp. Adjust bracket so flat in bracket runs parallel with motorcycle. Figure 6 and 7 4. Loosely install one M8 x 16 screw. (6mm Hex Key) Figure 7 Right Side Upper Mount Assembly 5. Place the second inside black clamp on the right fork tube.

SUZUKI M109 BRAKE PEDAL INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
1. Remove the pinch bolt from the bottom of the stock brake pedal. Notice that the slot in the pedal aligns with a punch mark on the end of the shaft. Using a needle- nose pliers disconnect the return spring from the pedal. Remove the pedal by sliding it outward until it touches the foot peg mount and then pushing the shaft inward. 2. Remove the pinch bolt from the new brake pedal and install it so that the slot is aligned with the punch mark on the end of the shaft. Install the pinch bolt and tighten it securely. Reconnect the pedal return spring

SUZUKI M109 PASSENGER FLOORBOARDS RELOCATION ARMS

0

Filed Under (Suzuki) by admin on 23-12-2010

download
1. If you are installing the relocation arms at the same time as the floorboards follow their instructions first and then refer to this sheet. 2. Fold the floorboards up, remove the allen screws that attach them to the round spacers, remove the floorboards and set aside. 3. Install the left and right relocation arms (marked with an L and R on the back side) onto the pins of the round spacers in the upper or lower position as desired. Using the allen screws and washers supplied bolt the arms to the round spacers and tighten securely. 4. Re-install the floorboards onto the relocation arms placing the supplied dowel pins into the set of holes on the relocation arms that allow the floorboards to be level or parallel with the ground. Install and tighten the allen screws removed earlier

SUZUKI M109 TURN SIGNAL RELOCATION BAR

0

Filed Under (Suzuki) by admin on 21-12-2010

download
1. Remove the windscreen/headlamp assembly by removing the two (2) 4mm allen screws located on the sides of the windscreen and the two plastic rivets at the top rear (push the center pin inward º” and then pull the rivet out). Pull the windscreen/headlamp forward to gain access to the rear, unplug the headlamp and set aside. 2. Locate the turn signal wire connections and unplug them from the wire harness. On the black connectors lift the tab up to unlock the connector and on the white ones use a small screwdriver inserted into one of the two longer slots and lift the center portion up while pulling the connector apart. Remove the screws which attach the turn signals to the chrome signal mounts located on the bottom of the mounts. Pull the turn signals out from the mounts and set aside. Looking thru the hole in the mount that the turn signals were in you will see a 4mm allen screw on each side, remove these. Remove remaining two (2) 6mm allen screws located on the bottom of the steering head that attach the mounts, remove and set aside. 3. Lay out the new turn signal mounting bar (see photo). Install the signals onto the bar as shown routing the wires thru the bar and out thru the slot in the center. Install the two (2) 6 x 8mm screws supplied and tighten securely. 4. Install the bar/signal assembly onto the steering head using the two (2) 6mm allen screws removed earlier (the brake hose clip should be on the bottom below the signal mount) and tighten securely. 5. Reconnect the turn signal wires (the pale blue/green wire goes to the right signal). Turn the ignition on and test the functions of the signals and running lights. Re-install the windscreen/headlamp assembly being sure to first plug in the headlamp