Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON CHROME ON/OFF SWITCH CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 1 2 is0771a 1. Auxiliary accessory housing cover 2. Cover screw (2) Figure 1. Auxiliary Accessory Housing 2. ALL models: If the Auxiliary Accessory Housing Kit and the Rocker Switch(es) ARE NOT already installed on the motorcycle handlebar: a. Proceed to Step 3 of these instructions. Install a chrome switch cap onto each switch before installing the Auxiliary Accessory Housing Kit onto the vehicle. If the Auxiliary Accessory Housing IS already installed on the motorcycle handlebar: a. See Figure 1. Using a T-25 TORX® driver, remove the two screws (2) retaining the Auxiliary Accessory Housing cover (1), and remove the cover. b. See Figure 2. Remove the switch mounting bracket, along with any attached switch(es) and accessories, from the switch housing. Note: it is not necessary to remove the switch from the mounting bracket, or to disconnect the switch wiring to replace the switch caps

HARLEY DAVIDSON CRUISE CONTROL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION NOTE if the motorcycle is equipped with the optional Harley-Davidson Smart Siren, the main fuse MUST be removed BEFORE the alarm is activated. This WILL happen within 5 seconds of turning the ignition switch to the OFF position (except for HD- Japan models). If the main fuse is not removed promptly, the siren WILL SOUND. 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. For FLHT, FLHTC, FLHX, FLHXXX and FLTRX models: Remove the outer fairing per the instructions in the service manual. For FLHR models: Follow the instructions in the service manual to remove only the handlebar clamp shroud. Removing the nacelle is not necessary. a. Remove the windshield and headlamp door. Remove the headlamp housing assembly. b. Release the chrome trim strip at the top of the nacelle. c. Remove the two Phillips screws beneath the fork lock plate. d. Loosen the Phillips screw at the front of the handlebar clamp shroud, and the four acorn nuts on the side of the headlamp nacelle. e. Raise the shroud slightly, separate the nacelle halves and slide the shroud forward to remove it from the nacelle. NOTE Before disconnecting the handlebar switch wiring, note the wire routing. 3. For ALL models: Refer to the service manual. Disconnect the right-side handlebar MOLEX socket housing from the black six-way main harness pin housing [22B] inside the fairing or headlamp nacelle

Victory V92SC Sport Cruiser COMFORT SPORT HANDLEBAR REMOVAL AND INSTALLATION

0

Filed Under (Victory) by admin on 13-11-2010

download
1. Remove wiring harness dart clips. 2. Disconnect clutch switch connector. 3. Remove 2screwsforclutch lever bracket clamp, remove clutch lever bracket from handlebar. 4. Remove screws for left handlebar switch assembly. Disconnect fast idle cable from lever. Remove switch assembly. 5. Grasp left grip end firmly. While twisting grip end back&forth, pull grip end off and discard. 6. Remove left grip by insertingathin screwdriver between the grip and handlebar end. Spray as mall amount of water/soap solution into the area between the grip and handlebar end. Aggressively twist the grip back-and-forth while simultaneously pulling the grip off. 1. Locate accessory handlebar. 2. Clean inside of throttle grip assembly and throttle cable flange grooves. Ill. 1. 3. Clean throttle grip area. Ill. 1. 4. Slide throttle assembly onto right handlebar end (cableshavenot been removed and should still be attached to the throttle tube). 5. Position the handlebar over the top of the triple clamp and reinstall using bolts removed instep 10. of handlebar removal. Torque to 30 ft. lbs. 6. Install right handlebar switch housing onto handlebar. NOTE: Make sure that locating pin of switch assembly aligns with hole in handlebars. 7. Install right handlebar switch housing screws, make sure locating pin properly aligns with hole in handlebar. Tighten screws to specified torque. 8. Install master cylinder and clamp, install screws. 9. Torque screws to specification. 10. Connect front brake switch wiring harness. 11. Install fast idle cable onto fast idle lever. 12. Clean inside of left grip and handlebar grip surfaces

Incoming search terms:

Incoming search terms: