HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

HARLEY DAVIDSON SPORTSTER CHOPPED FENDER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION Preparation 1. Position the vehicle on a motorcycle lift under the frame so the vehicle is upright and level. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 3. Remove the battery from the vehicle per the instructions in the service manual. 4. Raise the rear of the vehicle to relieve the load on the shock absorbers. 5. Follow the service manual instructions to remove only the bottom end shock absorber fasteners on each side of the vehicle. Save the fasteners for later assembly. 6. Raise the rear of the vehicle further to allow access to the underside of the rear fender. 7. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. Rear Fender Removal NOTE Note the location and orientation of rear fender mounting hardware, and save for later assembly. 1. Refer to the service manual and follow the instructions given to remove the rear fender, with the following exceptions: a. Removal of the tail lamp from the fender is not necessary. Rear Lamp Wiring 1. Cut off and discard the socket housings and terminal ends from the turn signal wires. 2. See Figure 1. Unscrew and remove the turn signal stalk (15) from one of the turn signal lamps, and discard. Remove and retain the turn signal lamp and support (14) from the rear fender support cover. 3. Insert the blade of a small screwdriver into the slot at the bottom of the turn signal lamp lens (2), and twist to unsnap the lens from the housing (1)

HARLEY DAVIDSON VRSCF LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
REMOVAL 1. See Figure 1. Remove four rear fender mounting bolts (1) and washers (2). If necessary, move the ECM to access the four fender mounting bolts. 2. Disconnect the tail lamp following the instructions in the appropriate service manual. 1 2 is05463 1. Bolt (4) 2. Washer (4) Figure 1. Fender Mounting Bolts INSTALLATION NOTE There are bosses molded into the inside of the fender to use as the hole drilling templates. 1. See Figure 2. Apply masking tape to the outside painted surface of the fender at the three hole locations (1 and 2). This will protect the painted surface during the drilling operation. 2. Put the fender on a work bench, painted surface down. Use clean, soft cloth between the fender and the work bench to protect the paint finish. NOTES Drilling each hole in the fender is a two-step procedure that requires a specific type of drill bit to avoid damaging the fender. 3. See Figure 2. Use a 1/2-inch spade bit or 1/2-inch unibit (do not use a spiral-type drill bit) to drill three holes from the inside of the fender through the three pilot hole bosses (1 and 2). Stop drilling when the tip of the bit just pierces the outside surface of the fender. 4. Turn the fender over so the painted surface is now facing up. Complete each hole by using the same 1/2-inch drill bit at each of the pierced holes. Clean excess material from the holes and clean the fender surface of any debris. 5. See Figure 5. Remove the masking tape from the holes and apply the protective tape (3) to the painted surface using the drilled holes for alignment. 6. See Figure 3. Put the luggage rack (1) upside down on the work bench and align the holes in the luggage rack with the holes in the fender (2).

HARLEY DAVIDSON VRSCF RIGID SADDLEBAGS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Kit Contents See Figure 5 and Table 1. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the rider seat and passenger pillion per the instructions in the service manual. 3. See Figure 1. Remove the four rear fender mounting bolts (1) and washers (2), and the passenger grab strap (3). If necessary, move the ECM to better access the fender mounting bolts. 1 3 2 is05463a 1. Bolt (4) 2. Washer (4) 3. Grab strap Figure 1. Fender Mounting Bolts 4. Disconnect the six-way tail lamp socket housing and four- way turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness. 5. If a luggage rack, sissy bar upright or both have been mounted on the rear fender , remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. NOTE The rack and/or upright will remain attached to the rear fender when the fender is removed. 6. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure 2. Remove the two bolts (8) holding the side license-plate bracket (1) to the seat pan (9). c. Remove the license-plate adjuster bracket (2) carriage bolt (3), washer (4) and lock nut (5), and the license- plate illuminator (6) and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (1), screws (7) and bolts (8) can be discarded. Set the remaining items aside for installation to the new side license-plate bracket. 8. Remove and discard the rear side reflectors (10). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. NOTE Access to the shock absorber adjustment collar is more difficult with the saddlebags in place. 9. Adjust the rear suspension preload, if desired, per the instructions in the service manual

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

Incoming search terms:

HARLEY DAVIDSON SOFTAIL TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 2. Raise the motorcycle on a floor jack to lower the rear wheel for fender hardware access. 3. See Figure 1. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 1. Remove Tail Lamp Lens 4. See Figure 2. Using a Terminal Pick Tool (1), press locking tabs and disconnect turn signal connectors (2-place, Items 2 and 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. NOTE FXST/S/B tail lamp and connectors are positioned 180° from orientation shown in Figure 2. 6. Reach under fender to locate clips fastening turn signal wires in place. Carefully pull wires out of clips, and pull turn signal connectors and wires out from under fender. a. Remove two-inch (51 mm) section of conduit 4 inches (102 mm) from turn signal connectors. b. Cut black turn signal wire about 5-1/2 inches (140 mm) from its connector. c. Cut violet/brown turn signal wire about 4-1/2 inches (114 mm) from its connector. d. Save cut wires with respective turn signal connectors. 7. Remove the sissy bar and/or sideplate assembly, if equipped